Install Glass Rock | Heat & Glo LifeStyle LUX60 instruction

D. Install Glass Rock

•Thirty pounds of black glass rock is provided with this appliance.

Note: Rinse the glass rocks with clear water and allow to dry before installation.

•Spread glass rock evenly across hearth pan to just cover metal pan. See Figure 15.8.

•Ensure that no glass rock is blocking any ports on burner tubes. The area between the rock shield and the back burner tube MUST be kept open as shown in Figure 15.9.

WARNING! Risk of Fire or Explosion! DO NOT cover burner ports with rock. This could prevent cross-over igni- tion, resulting in delayed or no ignition to this burner.

WARNING! Choking Hazard! Keep glass rock out of reach of children.

IMPORTANT! This appliance should be run three to four hours on low on the initial start-up. Turn it off and let it cool completely. Remove and clean the glass. Reinstall the glass and run the appliance for an additional 12 hours. This will help cure the products used in the paint.

Figure 15.8 Install Glass Rock

NO ROCK IN THIS AREA!

Figure 15.9 DO NOT Block Ports!

Heat & Glo • LUX60 • 4062-116 • Rev. G • 4/11

51

Image 51

Heat & Glo LifeStyle LUX60 owner manual Install Glass Rock

Contents

Models Installation and Operation Homeowner Reference Information Congratulations Table of Contents Reference Materials Limited Lifetime Warranty  B. Limited Lifetime Warranty Warranty Conditions Listing and Code Approvals Requirements for the Commonwealth of Massachusetts Gas Fireplace Safety Operating InstructionsYour Fireplace Operation of the LUX60 Fixed Glass AssemblyClear Space Decorative Doors and Fronts Before Lighting Fireplace Matching Security CodesSystem Operation IntelliFire Ignition System IPI Lighting Instructions For Your Safety Read Before Lighting Frequently Asked Questions Initial Break-in ProcedureAfter Fireplace is Lit Maintenance and Service Maintenance Tasks-HomeownerGlass Cleaning Remote Control Doors, Surrounds, FrontsVenting Control Compartment and Firebox Top Maintenance Tasks-Qualiﬁed Service TechnicianGasket Seal and Glass Assembly Inspection Firebox LED Light Bar Replacement Light Glass Replacement/Cleaning Back Clean Porcelain Panels Remove Screws Typical Appliance System Getting Started Design and Installation Considerations Tools and Supplies NeededInspect Appliance and Components Framing and Clearances Select Appliance LocationAssemble Steel Stud Kit Clearances Construct the Appliance Chase Clearances to Combustibles Vent Termination Minimum Clearances Termination Locations Minimum Clearances for Termination Use of Elbows Vent Information and DiagramsApproved Pipe Vent Table Key Vent Diagrams Top Vent Horizontal TerminationOne Elbow Three Elbows Two 45 Elbows replacing One 90 Elbow Top Vent Vertical Termination No ElbowTwo Elbows Combustible Wall Penetration Vent Clearances and FramingPipe Clearances to Combustibles Wall Penetration Framing Ceiling ﬁrestop Must be used between ﬂoors and at- tics Install the Ceiling Firestop Install Attic Insulation Shield Flat Ceiling InstallationVaulted Ceiling Installation Secure and Level the Appliance Appliance Preparation Assemble Pipe Sections Install Vent PipeAttach Pipe to the Firebox Assembly Assemble Vent Sections Secure the Vent Sections Assemble Slip Sections Disassemble Vent Sections Install Metal Roof Flashing 13 Assembling the Storm Collar Assemble and Install Storm Collar Heat Shield Requirements for Horizontal Termination Install Vertical Termination Cap 16 Venting through the wall Install Horizontal Termination Cap Open Top Shroud may be used with DVP-TV, DVP-TVHW ShroudsHHT Shrouds Field Constructed Shrouds Roofed Style Shroud may be used with DVP-TV, DVP-TVHW Mailbox Style Shroud may be used with DVP-TV, DVP-TVHW Gas Information Gas PressureGas Connection Setting Flame Height/Manifold Pressure Install Flame Solenoid Wiring Requirements Electrical Service and RepairElectrical Information Junction Box Detail Junction Box Installation Standard 1/2 in mm Sheetrock Wall Finishing Additional Decorative Finishing over 1 in mm Thick Additional Decorative Finishing up to 1 in mm Thick Clean the Appliance Appliance SetupRemove Glass Assembly Air Shutter Access & Adjustment Center Burner Tube Air Shutter Outside Burner Tube Air Shutter Adjustment Install Glass Rock Install Glass Rock IntelliFire IPI Ignition System Troubleshooting IntelliFire IPI Ignition System Reference Materials Appliance Dimension Diagram DVP45 Vent Components Diagrams DVP-TRAPFL DVP-TVHW DVP-TRAP Optional Components Do not Discard this Manual Contact Information