Dvp-Tvhw | Heat & Glo LifeStyle LUX60 specification

B. Vent Components Diagrams (continued)

7-1/4 in.

(184 mm)

12-1/2 in.

(318 mm)

5-1/4 in.

(133 mm)

DVP-TVHW

Vertical Termination Cap (High wind)

16-7/8 in.	14 in.
(429 mm)	(356 mm)

12 in.

(305 mm)

7-1/8 in.

12-1/8 in.(181 mm)

(314 mm)

8-3/4 in.

(222 mm)

1-5/8 in.

(41 mm)

DVP-HPC

High Performance Cap

Figure 17.4 DVP Vent Components

Heat & Glo • LUX60 • 4062-116 • Rev. G • 4/11

57

Image 57

Heat & Glo LifeStyle LUX60 owner manual Dvp-Tvhw

Contents

Models Installation and Operation Homeowner Reference Information Congratulations Table of Contents Reference Materials Limited Lifetime Warranty  B. Limited Lifetime Warranty Warranty Conditions Listing and Code Approvals Requirements for the Commonwealth of Massachusetts Gas Fireplace Safety Operating InstructionsYour Fireplace Clear Space Fixed Glass AssemblyDecorative Doors and Fronts Operation of the LUX60 Before Lighting Fireplace Matching Security CodesSystem Operation IntelliFire Ignition System IPI Lighting Instructions For Your Safety Read Before Lighting Frequently Asked Questions Initial Break-in ProcedureAfter Fireplace is Lit Maintenance and Service Maintenance Tasks-HomeownerGlass Cleaning Remote Control Doors, Surrounds, FrontsVenting Gasket Seal and Glass Assembly Inspection Maintenance Tasks-Qualiﬁed Service TechnicianFirebox Control Compartment and Firebox Top LED Light Bar Replacement Light Glass Replacement/Cleaning Back Clean Porcelain Panels Remove Screws Typical Appliance System Getting Started Design and Installation Considerations Tools and Supplies NeededInspect Appliance and Components Framing and Clearances Select Appliance LocationAssemble Steel Stud Kit Clearances Construct the Appliance Chase Clearances to Combustibles Vent Termination Minimum Clearances Termination Locations Minimum Clearances for Termination Approved Pipe Vent Information and DiagramsVent Table Key Use of Elbows Vent Diagrams Top Vent Horizontal TerminationOne Elbow Three Elbows Two 45 Elbows replacing One 90 Elbow Top Vent Vertical Termination No ElbowTwo Elbows Pipe Clearances to Combustibles Vent Clearances and FramingWall Penetration Framing Combustible Wall Penetration Ceiling ﬁrestop Must be used between ﬂoors and at- tics Install the Ceiling Firestop Install Attic Insulation Shield Flat Ceiling InstallationVaulted Ceiling Installation Secure and Level the Appliance Appliance Preparation Attach Pipe to the Firebox Assembly Install Vent PipeAssemble Vent Sections Assemble Pipe Sections Secure the Vent Sections Assemble Slip Sections Disassemble Vent Sections Install Metal Roof Flashing 13 Assembling the Storm Collar Assemble and Install Storm Collar Heat Shield Requirements for Horizontal Termination Install Vertical Termination Cap 16 Venting through the wall Install Horizontal Termination Cap HHT Shrouds ShroudsField Constructed Shrouds Open Top Shroud may be used with DVP-TV, DVP-TVHW Roofed Style Shroud may be used with DVP-TV, DVP-TVHW Mailbox Style Shroud may be used with DVP-TV, DVP-TVHW Gas Information Gas PressureGas Connection Setting Flame Height/Manifold Pressure Install Flame Solenoid Wiring Requirements Electrical Service and RepairElectrical Information Junction Box Detail Junction Box Installation Standard 1/2 in mm Sheetrock Wall Finishing Additional Decorative Finishing over 1 in mm Thick Additional Decorative Finishing up to 1 in mm Thick Remove Glass Assembly Appliance SetupAir Shutter Access & Adjustment Clean the Appliance Center Burner Tube Air Shutter Outside Burner Tube Air Shutter Adjustment Install Glass Rock Install Glass Rock IntelliFire IPI Ignition System Troubleshooting IntelliFire IPI Ignition System Reference Materials Appliance Dimension Diagram DVP45 Vent Components Diagrams DVP-TRAPFL DVP-TVHW DVP-TRAP Optional Components Do not Discard this Manual Contact Information