D. Mantel Projections, To perpendicular wall

D. Mantel Projections

30 in. minimum

to ceiling

			18
			17
			17
	15		16
			16
					17-3/4
					17-3/4
13	14			17
	14			17
			16-1/4
			16-1/4
3 - 12		15-1/2
3 - 12		15-1/2
0 - 3	14-3/4
14
13-1/4
9-3/8

Measured from top of hood (in inches)

Figure 3.3 Clearances to Mantels or Other Combustibles Above Appliance

Top of

Appliance

Drywall

48 in.

(1219 mm)

B max.

Mantel Leg or Perpendicular Wall

A1 in. (25mm) min.

to perpendicular wall

B3-1/2 in. (89 mm) min. from fireplace opening to perpendicular wall

Figure 3.4 Clearances to Combustible Mantel Legs or Wall Projec- tions (acceptable on both sides of opening)

Heatilator • GB4336/GB4992 • 4003-085 Rev H • 04/06

Page 11

Image 11

Heatiator GB4336 owner manual D. Mantel Projections, Top of Appliance Drywall A 48 in 1219 mm B max, to perpendicular wall

Contents

B-VentGas Appliance What to do if you smell gasModels GB4336, GB4336L GB4336I, GB4336IL GB4942, GB4942L GB4942I, GB4942IL Gas Type Homeowner Reference InformationListing Label Information/Location Congratulations 12 Appliance Setup Table of Contents5 Vent Information and Diagrams 8 Installing Vent Pipe C. BTU Speciﬁcations D. High Altitude Installations1Listing and Code Approvals A. Appliance Certiﬁcation 2Getting Started A. Design and Installation Considerations Asphyxiation Risk B. Negative PressureNegative Pressure Any such action may cause a ﬁre hazard C. Tools and Supplies NeededD. Inspect the Appliance and Components Fire Risk 3Framing and ClearancesA. Select Appliance Location Fire Risk B. Construct the Appliance Chase Fire Risk Odor Risk C. Clearances to perpendicular wall D. Mantel ProjectionsTop of Appliance Drywall A 48 in 1219 mm B max Mantel Leg or Perpendicular Wall A1 in. 25mm min Fire Risk Explosion Risk 4Termination LocationsA. Vent Termination Minimum Clearances Fire Risk Asphyxiation Risk 5Vent Information and DiagramsA. Vent Guidelines B. Vent System Conﬁguration Fire Risk Explosion Risk Vent supports C. Vertical Penetration Framing 6Vent Clearances and FramingA. Pipe Clearances to Combustibles B. Wall Penetration Framing Fire Risk Asphyxiation Risk A. Installing Outside Air Kit Damper AssemblyAppliance Preparation Risk of Smoke Spillage both sides B. Gas and Electrical ConnectionsC. Securing and Leveling Appliance Nailing Tabs C. Securing Vent Sections 8Installing Vent PipeB. Attach Vent to Firebox Assembly A. Assemble Vent Sections B. Gas Pressure 9Gas InformationA. Fuel Conversion C. Gas Connection Fire Risk Explosion Risk Asphyxiation Risk D. High Altitude InstallationsFire Risk Explosion Risk Gas build-upduring line purge may ignite 10 Electrical Information A. Recommendation for WireB. Connecting to the Appliance C. Intelliﬁre Ignition System Wiring Optional Junction Box Wiring D. Standing Pilot Ignition System WiringOptional Accessories Requirements E. Junction Box Installation Fire Risk 11 FinishingA. Mantel Projections B. Facing Material D.Install the Refractory 12 Appliance SetupB. Clean the Appliance C. Accessories F. Log Removal/Replacement Fire Risk Combustion Fumes Risk I. Air Shutter SettingG. Glass Doors H. Hood SEVERE BURNS MAY RESULT 13 Operating InstructionsA. Before Lighting Appliance Fire Risk Burn Risk HOT! DO NOT TOUCH Without C. High Limit Safety SwitchB. Check Appliance Draft Note to Qualiﬁed Service Technician LIGHTING INSTRUCTIONS D. Lighting the ApplianceWARNING RISK OF FIRE FOR YOUR SAFETY READ BEFORE LIGHTING TO TURN OFF GAS TO APPLIANCE FOR YOUR SAFETY READ BEFORE LIGHTINGNATURAL GAS LIGHTING INSTRUCTIONS Issue F. Frequently Asked QuestionsE. After the Appliance is Lit Initial Break-inProcedure Possible Causes 14 TroubleshootingA. Standing Pilot Ignition System Symptom Frequent pilot outage SymptomPossible Causes Corrective Actions Corrective Actions B. Intelliﬁre Ignition SystemSymptom Possible Causes Pilot sparks, but pilot will SymptomPossible Causes Corrective Actions Risk of injury or property damage 15 Maintaining and Servicing the ApplianceClean When cleaning glass door one is not present Maintenance and Service TasksMaintenance Tasks Inspect Model A. Appliance Dimension Diagram16 Reference Materials Figure 16.1 Appliance Dimensions Exploded Parts Diagram Service PartsB. Service Parts List GB4336 SERIES GB4336 Service PartsGB4336 SERIES Description of Part Service Parts List Standing Pilot Valve AssemblyIntermittent Pilot Valve Assembly Service Parts GB4336 Service PartsGB4336 SERIES Description of Part Beginning Manufacturing Date 1/19/04 GB4942 SERIESService Parts Exploded Parts Diagram GB4942 Service PartsGB4942 SERIES # Description of Part Service Parts List Service PartsStanding Pilot Valve Assembly Intermittent Pilot Valve Assembly GB4942 Service PartsGB4942 SERIES # Description of Part UD4 Uninsulated Duct 4 in. 102 mm 42 in 1067 mm C. Optional ComponentsID4 Insulated Duct in. 102 mm This page intentionally left blank This page intentionally left blank 1 Year Limited Warranty D. Limited Lifetime WarrantyGas Appliance Fireplace Limited Lifetime Warranty Limited Lifetime Warranty DO NOT DISCARD THIS MANUAL E. Contact InformationHearth & Home Technologies Inc 1915 W. Saunders Street Mt. Pleasant, Iowa

Heatiator GB4336 D. Mantel Projections, Top of Appliance Drywall A 48 in 1219 mm B max

Models: GB4336

D. Mantel Projections

Top of

Mantel Leg or Perpendicular Wall

to perpendicular wall