Manuals / Heatiator / Household Appliance / Indoor Fireplace

Heatiator GB4336 owner manual 2Getting Started, A. Design and Installation Considerations

Models: GB4336

1 52

Download 52 pages 25.36 Kb

Page 5

2Getting Started

2Getting Started

A. Design and Installation Considerations

Heatilator B-vent gas appliances are designed to operate with all exhaust gases expelled to the outside of the building, and combustion air pulled from the room.

CAUTION

Check building codes prior to installation.

•Installation MUST comply with local, regional, state and national codes and regulations.

•Consult insurance carrier, local building, fire ofﬁ cials or authorities having jurisdiction about restrictions, installation inspection, and permits.

When planning an appliance installation, it’s necessary to determine the following information before installing:

•Where the appliance is to be installed. See Section 3.

•The vent system conﬁ guration to be used. See Sections 4 and 5.

•Gas supply piping. See Section 9.

•Electrical wiring. See Sections10

•Framing and finishing details. See Sections 3, 6 and 11.

•Whether optional accessories—devices such as a fan, wall switch, or remote control—are desired. See Section 10.

WARNING

Keep appliance dry.

•Mold or rust may cause odors.

•Water may damage controls.

Heatilator • GB4336/GB4992 • 4003-085 Rev H • 04/06

5

Image 5

Heatiator GB4336 owner manual 2Getting Started, A. Design and Installation Considerations

Contents

Models GB4336, GB4336L GB4336I, GB4336IL What to do if you smell gasGB4942, GB4942L GB4942I, GB4942IL B-VentGas ApplianceListing Label Information/Location Homeowner Reference InformationCongratulations Gas Type5 Vent Information and Diagrams Table of Contents8 Installing Vent Pipe 12 Appliance Setup1Listing and Code Approvals D. High Altitude InstallationsA. Appliance Certiﬁcation C. BTU Speciﬁcations2Getting Started A. Design and Installation ConsiderationsAsphyxiation Risk B. Negative PressureNegative Pressure Any such action may cause a ﬁre hazard C. Tools and Supplies NeededD. Inspect the Appliance and Components Fire Risk 3Framing and ClearancesA. Select Appliance Location Fire Risk B. Construct the Appliance ChaseFire Risk Odor Risk C. ClearancesTop of Appliance Drywall A 48 in 1219 mm B max D. Mantel ProjectionsMantel Leg or Perpendicular Wall A1 in. 25mm min to perpendicular wallFire Risk Explosion Risk 4Termination LocationsA. Vent Termination Minimum Clearances A. Vent Guidelines 5Vent Information and DiagramsB. Vent System Conﬁguration Fire Risk Asphyxiation RiskFire Risk Explosion Risk Vent supportsA. Pipe Clearances to Combustibles 6Vent Clearances and FramingB. Wall Penetration Framing C. Vertical Penetration FramingAppliance Preparation A. Installing Outside Air Kit Damper AssemblyRisk of Smoke Spillage Fire Risk Asphyxiation RiskC. Securing and Leveling Appliance B. Gas and Electrical ConnectionsNailing Tabs both sidesB. Attach Vent to Firebox Assembly 8Installing Vent PipeA. Assemble Vent Sections C. Securing Vent SectionsA. Fuel Conversion 9Gas InformationC. Gas Connection B. Gas PressureFire Risk Explosion Risk D. High Altitude InstallationsGas build-upduring line purge may ignite Fire Risk Explosion Risk Asphyxiation RiskB. Connecting to the Appliance A. Recommendation for WireC. Intelliﬁre Ignition System Wiring 10 Electrical InformationOptional Junction Box Wiring D. Standing Pilot Ignition System WiringOptional Accessories Requirements E. Junction Box Installation A. Mantel Projections 11 FinishingB. Facing Material Fire RiskB. Clean the Appliance 12 Appliance SetupC. Accessories D.Install the RefractoryF. Log Removal/Replacement G. Glass Doors I. Air Shutter SettingH. Hood Fire Risk Combustion Fumes RiskA. Before Lighting Appliance 13 Operating InstructionsFire Risk Burn Risk HOT! DO NOT TOUCH SEVERE BURNS MAY RESULTB. Check Appliance Draft C. High Limit Safety SwitchNote to Qualiﬁed Service Technician WithoutWARNING RISK OF FIRE D. Lighting the ApplianceFOR YOUR SAFETY READ BEFORE LIGHTING LIGHTING INSTRUCTIONSNATURAL GAS FOR YOUR SAFETY READ BEFORE LIGHTINGLIGHTING INSTRUCTIONS TO TURN OFF GAS TO APPLIANCEE. After the Appliance is Lit F. Frequently Asked QuestionsInitial Break-inProcedure Fire Risk High TemperaturesA. Standing Pilot Ignition System 14 TroubleshootingSymptom Possible CausesPossible Causes SymptomCorrective Actions Frequent pilot outageSymptom B. Intelliﬁre Ignition SystemPossible Causes Corrective ActionsPossible Causes SymptomCorrective Actions Pilot sparks, but pilot willClean 15 Maintaining and Servicing the ApplianceWhen cleaning glass door Risk of injury or property damageMaintenance Tasks Maintenance and Service TasksInspect one is not present16 Reference Materials A. Appliance Dimension DiagramFigure 16.1 Appliance Dimensions ModelB. Service Parts List Service PartsGB4336 SERIES Exploded Parts DiagramGB4336 SERIES Service PartsDescription of Part GB4336Intermittent Pilot Valve Assembly Standing Pilot Valve AssemblyService Parts Service Parts ListGB4336 SERIES Service PartsDescription of Part GB4336Service Parts GB4942 SERIESExploded Parts Diagram Beginning Manufacturing Date 1/19/04GB4942 SERIES Service Parts# Description of Part GB4942Standing Pilot Valve Assembly Service PartsIntermittent Pilot Valve Assembly Service Parts ListGB4942 SERIES Service Parts# Description of Part GB4942ID4 Insulated Duct C. Optional Componentsin. 102 mm UD4 Uninsulated Duct 4 in. 102 mm 42 in 1067 mmThis page intentionally left blank This page intentionally left blank Gas Appliance Fireplace Limited Lifetime Warranty D. Limited Lifetime WarrantyLimited Lifetime Warranty 1 Year Limited WarrantyHearth & Home Technologies Inc E. Contact Information1915 W. Saunders Street Mt. Pleasant, Iowa DO NOT DISCARD THIS MANUAL