|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| English |
| |||
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| |
Nailer is not | Obstruction keep- | Clear obstruction, trash, bent |
|
|
|
| |
always driving | ing the nail clip | or twisted nails, etc. Make sure |
|
|
|
| |
a nail (cont.) | from advancing. | Pusher provides positive push- |
|
|
|
| |
|
| ing force on the Nail clip to |
|
|
|
| |
|
| prevent Nails from turning |
|
|
|
| |
|
|
|
|
|
|
| |
Air is escaping | Damaged or worn | Contact Hitachi for replace- |
|
|
|
| |
| seal. | ment. |
|
|
|
| |
|
|
|
|
|
|
|
|
| Oil has been used | Contact Hitachi for replace- |
|
|
|
| |
|
|
|
|
| |||
| causing | ment. |
|
|
|
| |
| to swell which can |
|
|
|
|
|
|
| restrict movement |
|
|
|
|
|
|
| of piston or other |
|
|
|
|
|
|
| component that |
|
|
|
|
|
|
| must seal. |
|
|
|
|
|
|
|
|
|
|
|
|
| |
Nailer is driving | Gate (Ref. #22) | Disconnect air supply; clear |
|
|
|
| |
two nails. | is loose or is not | nails from tool; reinstall the |
|
|
|
| |
| seated properly | Gate (Ref. #22). |
|
|
|
| |
|
|
|
|
|
|
|
|
| End of Rail (Ref. | Turn Rail (Ref. #26) around to |
|
|
|
| |
|
|
|
|
| |||
| #26) is worn or | use other end in Guide if this |
|
|
|
| |
| damaged. | has not been previously done. |
|
|
|
| |
|
| If Rail has already been turned |
|
|
|
| |
|
| previously, replace Rail. |
|
|
|
| |
|
|
|
|
|
|
|
|
| Screws holding | Tighten Screws (Ref. #43, #29) |
|
|
|
| |
|
|
|
|
| |||
| Magazine (Ref. | that secure the Magazine (Ref. |
|
|
|
| |
| #29) may be loose | #28) to the Guide (Ref. #21) and |
|
|
|
| |
| preventing Rail | the back Magazine Retainer |
|
|
|
| |
| (Ref. #26) from be- | Bracket (Ref. #27). |
|
|
|
| |
| ing held properly in |
|
|
|
|
|
|
| place. |
|
|
|
|
|
|
|
|
|
|
|
|
| |
Nails are not be- | Not driving Nails | Always drive Nails into the |
|
|
|
| |
ing counter sunk | into the tongue | tongue area, not the groove. |
|
|
|
| |
into wood and | area |
|
|
|
|
|
|
are left sticking |
|
|
|
|
|
|
|
out of wood. |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| Tip of Driver Blade | Contact Hitachi for replace- |
|
|
|
| |
|
|
|
|
| |||
| (Ref. #58) broken | ment. |
|
|
|
| |
|
|
|
|
|
|
|
|
| Air pressure too | Set air pressure to |
|
|
|
| |
|
|
|
|
| |||
| low |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| Using air compres- | Follow recommendations in the |
|
|
|
| |
|
|
|
|
| |||
| sor that is too small | Owner’s Manual relative to size |
|
|
|
| |
|
| and volume of air compressor. |
|
|
|
| |
|
| The ideal air compressor trip |
|
|
|
| |
|
| on pressure should be 115 PSI |
|
|
|
| |
|
| or above. |
|
|
|
| |
|
|
|
|
|
|
|
|
| Using an air line | Always use 3/8” ID air line. |
|
|
|
| |
|
|
|
|
| |||
| that is too small |
|
|
|
|
|
|
|
|
|
|
|
|
| |
|
| - Continued - |
|