Manuals / Hobart / Kitchen Appliance / Oven

Hobart HR5 manual Place the assembled rotor in the oven

Models: HR5

1 36

Download 36 pages 25.73 Kb

Page 9

Image 9

7.Place the assembled rotor in the oven.

8.Turn Rotisserie dial to to rotate rotor.

9.Turn Rotisserie dial to "0/P" to stop rotation when the hole pattern (Fig. 4) is located at the bottom of the oven.

10.Verify that the hole pattern is identical to the top illustrated hole pattern shown in Fig. 4.

11.If hole pattern does not match the top illustrated hole pattern, but does match the bottom illustrated hole pattern in Fig. 4:

a.Take rotor assembly out of oven.

b.Flip rotor assembly.

c.Place rotor assembly back in oven.

d.Repeat steps 8-10 above.

HR7

Fig. 4

PL-53381

– 9 –

Page 9

Image 9

Hobart HR5 manual Place the assembled rotor in the oven

Contents

T I O HR5 & HR7 ROTISSERIE OVENSHW5 & HW7 WARMERS HOBART CORPORATION TABLE OF CONTENTSSetting the Roasting Time Setting the TemperatureSetting an Early Warning Buzzer Setting End Time Delayed StartModel HR7 Oven Model HR5 OvenModel HW5 Warmer Model HW7 WarmerFeatures and Options Installation, Operation and Care of HR SERIES ROTISSERIE OVENS ANDHW SERIES ROTISSERIE WARMERS GENERALWARMERS OVENSASSEMBLY INSTALLATIONLOCATION LEGS / CASTERSAssembling the Rotor HR7 only 7. Place the assembled rotor in the oven ELECTRICAL CONNECTIONS Stacked Ovens or Oven and WarmerSingle Oven or Warmer PHASE ELECTRICAL DATAMODEL VOLTSBEFORE FIRST USE OPERATIONDisplay PROGRAMMABLE OVEN CONTROL PANEL WITH MANUAL CONTROLS FigProgrammable Controls Manual ControlsUsing Manual Controls Main Power DialMANUAL CONTROLS Fig Thermostat DialPROGRAMMABLE CONTROLS Fig Setting the Time of DayProgramming Menu Buttons Verifying Programmed Temperatures and TimesChanging a Programmed Setting Displaying Time/Temperature During a Processing CycleStarting a Processing Cycle Interrupting a Processing CycleSetting an Early Warning Buzzer Setting the End Time Delayed StartTurning the Buzzer Off Stopping the RotisserieAutomatic Controls AUTOMATIC OVEN CONTROL PANEL WITH MANUAL CONTROLS Fig DisplayMAIN POWER DIAL PL-53361 Manual ControlsUsing Manual Controls Main Power DialMANUAL CONTROLS Fig Thermostat DialSetting the Roasting Time Setting the TemperatureAUTOMATIC CONTROLS Fig DISPLAY TEMPSetting End Time Delayed Start Interrupting an Automatic Cooking OperationSetting an Early Warning Buzzer Resetting the Automatic Control Changing A SettingStopping an Automatic Cooking Operation Turning the Buzzer OFFPREPARING THE PRODUCT LOADING PRODUCTS ONTO ACCESSORIESLoading Products onto Spits V Spit StandardFork Spit Optional Turkey Spit OptionalLoading Products onto Chicken Racks Optional Load the chickens, breast up, in the basket Fig. 15 Loading Products in a Basket OptionalPL-41369-1 PL-41370-1LOADING ACCESSORIES INTO THE OVEN Loading Fork Spits Into Oven Loading Spits Into OvenPL-53379 PL-53378Loading Racks, Baskets, or Baking Plate Into Oven UNLOADING ACCESSORIES FROM OVENTemperature SUGGESTED ROASTING GUIDELINESInternal CapacityEmpty the grease drawer when necessary Be careful if grease is warm EMPTYING GREASE DRAWER3. Close drain valve when empty Fig 4. Slide grease drawer shut 1. Open door and slide grease drawer out about 5 13 cm FigWARMER CONTROLS Fig USING WARMERS Models HW5 and HW7CLEANING STAINLESS STEEL SURFACES CLEANINGCLEANING NONSTICK COATED SURFACES Do Not go longer than eight hours without cleaningCAUTION Cleaning should not be delayed beyond 8 hours of service How To Clean Nonstick Coated Surfaces Routine CleaningHow To Clean Severe Buildup on Nonstick Coated Surfaces CLEANING PROBECLEANING WARMERS CLEANING GREASE DRAWERCLEANING QUARTZ LAMPS MONTHLY CLEANINGMAINTENANCE SERVICEMODEL HR5 OVEN ONLY