Cable | HP AdvanceStack Internet Router guide

Cable Specifications

Synchronous Serial Cable Assemblies and Pinouts

Table A-10. V.35 DCE Cable Pinouts (DB-60 to 34-Pin)

Specifications	J1-50	MODE_0	Shorting group	–	–	–
	60 Pin	Signal	Description	Direction	34 Pin	Signal

	J1-49	MODE_1	Shorting group	–	–	–
	J1-48	GND
Cable
Cable	J1-51	GND
	J1-51	GND

	J1-53	TxC/NIL	Shorting group	–	–	–
	J1-54	RxC_TxCE
	J1-55	RxD/TxD
	J1-56	GND

	J1-46	Shield_GND	Single	–	J2-A	Frame GND

	J1-45	Circuit_GND	Twisted pair no. 12	–	J2-B	Circuit GND
	Shield	–		–	Shield	–

	J1-35	CTS/RTS	Twisted pair no. 8	<—	J2-C	RTS
	Shield	–		–	Shield	–

	J1-42	RTS/CTS	Twisted pair no. 9	—>	J2-D	CTS
	Shield	–		–	Shield	–

	J1-43	DTR/DSR	Twisted pair no. 10	—>	J2-E	DSR
	Shield	–		–	Shield	–

	J1-44	LL/DCD	Twisted pair no. 11	—>	J2-F	RLSD
	Shield	–		–	Shield	–

	J1-34	DSR/DTR	Twisted pair no. 7	<—	J2-H	DTR
	Shield	–		–	Shield	–

	J1-33	DCD/LL	Twisted pair no. 6	<—	J2-K	LT
	Shield	–		–	Shield	–

	J1-28	RxD/TxD+	Twisted pair no. 5	<—	J2-P	SD+
	J1-27	RxD/TxD–		<—	J2-S	SD–

	J1-18	TxD/RxD+	Twisted pair no. 1	—>	J2-R	RD+
	J1-17	TxD/RxD–		—>	J2-T	RD–

	J1-26	RxC/TxCE+	Twisted pair no. 4	<—	J2-U	SCTE+
	J1-25	RxC/TxCE–		<—	J2-W	SCTE–

	J1-22	NIL/RxC+	Twisted pair no. 3	—>	J2-V	SCR+
	J1-21	NIL/RxC–		—>	J2-X	SCR–

	J1-20	TxCE/TxC+	Twisted pair no. 2	—>	J2-Y	SCT+
	J1-19	TxCE/TxC–		—>	J2-AA	SCT–

A-16

Image 84

HP AdvanceStack Internet Router manual Table A-10. V.35 DCE Cable Pinouts DB-60 to 34-Pin

Contents

HP AdvanceStack Internet Router Page Support is as close As the World Wide Web Additional HP Support Services Installation Guide HP AdvanceStack Internet Router Publication Number Contents Configuring the HP AdvanceStack Internet Router Verifying Network Connectivity Getting More Information Cable Specifications Page HP AdvanceStack Internet Router Overview Hardware Features HP AdvanceStack Internet Router Overview Software Features Includes switching Compression Ordering Information Cables and Adapters Documentation and Software Cisco Systems Contact InformationCisco Systems, Inc West Tasman Drive San Jose, CA Tel Nets Fax Installation Verifying Included Parts Modem for remote access optional Installing the HP AdvanceStack Internet RouterRequired Tools and Parts Preparing to Connect to a Network Isdn BRI Cable Specifications S/T Cable Specification High-Capacitance Cable Low-Capacitance CableIsdn Connections Synchronous Serial Connections Typical DTE and DCE DevicesDevice Type Gender Typical Devices Or other DCE device EIA/TIA-232 Speed and Distance LimitationsData Rate Baud Distance Feet Distance Meters Console and Auxiliary Port Considerations U T I O N Console Port Connections Installing the Module While you are installing the moduleCircuitry on the boards Installation Connecting to the Network Connecting to a WAN Connecting the Console Terminal and Modem Connecting the Isdn BRI Port to an NT1 Device Connecting the Console Terminal Connecting a Modem to the Auxiliary Port What to Do After Installing the Router Hardware Booting the Router for the First Time Configuration Configuring the Router for the First Time Begin to configure the routerConfiguring the HP AdvanceStack Internet Router Using the System Configuration Dialog Parity, and 2 stop bits On the console screenReflect the screen displays on your console OK? Enter an enable secret password Enter the enable and virtual terminal passwords Isdn Switch Type Country Isdn Switch Type Description Configuring Ethernet or VG Interfaces Press Return or enter yes to configure serial port Configuration Using Configuration Mode Prompt changes to the privileged Exec prompt Using AutoInstall Router will now boot with the configuration you entered Cisco IOS Software Basics Cisco IOS Modes of Operation Mode Usage How to Enter the Mode Prompt Operation Interface serial 0 command toCisco IOS Operating Modes Getting Context-Sensitive Help Configuring Isdn Saving Configuration Changes Router config# username targetrouter password abc Enter the exit command to exit interface configuration mode Example Isdn Configuration Enter the exit command to exit global configuration mode Example Isdn Configuration Router# config term Configuration Verifying Network ConnectivityGetting More Information Maintenance Reading the LEDs Troubleshooting LEDs on the Host Device Front PanelState Description LEDs on the HP AdvanceStack Internet Router Front Panel Isdn BRI Upgrading the Boot ROMs Recovering Lost Passwords Signal to the router Boot ROMs and ignore NvramEnter the initialize command to initialize the router Ration Dialog appears Passwords, if they are not encrypted, and proceed to step NvramAre different Press Ctrl-Z to exit configuration mode Or replace a password, proceed to and logReboot the router Configuration register value you set in step Virtual Configuration Register Settings 0x2102 is a combination of settingsVirtual Configuration Register Bit Meanings Bit No.a Hexadecimal Meaning Changing Configuration Register Settings Virtual configuration register is stored in NvramExplanation of Boot Field Configuration Register Bits 00 to Boot Field Boot Process Virtual Configuration Register Bit Meanings Default Boot Filenames Boot field number, a hyphen, and the processor typeOverrides the default boot filename Action or Filename Bit Bit Address net host Baud Bit Enabling Booting from Flash Memory Copying a Cisco IOS Image to Flash Memory Following messages display System reboots using the new image in Flash memory Command reference publications Back of HP Switching Hub Inserting the HP Internet Router Module into an HP Remote 2C Router to Router Connections Console and Auxiliary Port Signals Pinouts Cable Specifications Cable Specifications Identifying a Roll-Over Cable Console Port Signals and Pinouts Auxiliary Port Signals and Pinouts Figure A-2. Connecting the Auxiliary Port to a Modem Synchronous Serial Cable Assemblies and Pinouts EIA-530 Figure A-3. EIA-530 Serial Cable Assembly 60 Pin Signal 25 Pin DTE DCEa Table A-4.EIA-530 DTE Cable Pinouts DB-60 to DB-25Direction EIA/TIA-232 60 Pin Signal Description Direction 25 Pin Table A-5. EIA/TIA-232 DCE Cable Pinouts DB-60 to DB-25 Table A-6. EIA/TIA-232 DCE Cable Pinouts DB-60 to DB-25 Cable EIA/TIA-449 60 Pin Signal Description Direction 37 Pin Table A-7. EIA/TIA-449 DTE Cable Pinouts DB-60 to DB-37 Table A-8. EIA/TIA-449 DCE Cable Pinouts DB-60 to DB-37 Figure A-6. V.35 Cable Assembly Indicates DTE to DCE, and indicates DCE to DTE 60 Pin Signal Description Direction 34 Pin Table A-9. V.35 DTE Cable Pinouts DB-60 to 34-Pin Table A-10. V.35 DCE Cable Pinouts DB-60 to 34-Pin Cable Figure A-7. X.21 Cable Assembly Cable Specifications 60 Pin Signal Description Direction 15 Pin Table A-11. X-21 DTE Cable Pinouts DB-60 to DB-15 Table A-12. X.21 DCE Cable Pinouts DB-60 to DB-15 Isdn BRI Port and Cable Pinouts Table A-13. BRI Port RJ-45 PinoutRJ-45 TE b NT c Polarity Pin a Power Consumption HP J3138A SpecificationsPhysical Environmental Connectors ElectromagneticIEC 950 1991 + A1, A2 / .EN60950 I 1992 + A1, A2 Safety and Regulatory Statements Safety Information Safety and Regulatory Statements Informations concernant la sécurité Sicherheitssymbole Hinweise zur Sicherheit Considerazioni sulla sicurezza Simboli di sicurezza Consideraciones sobre seguridad Símbolos de seguridad Safety Information Japanese Statements Regulatory Statements No repairs can be done by the customer European Community CanadaUnshielded cables and EN55022 Page Index IndexIndex See also Isdn BRI Setup Page Page J3138-90003