Use the |
| following | guidelines |
| to | determine |
| the |
| correct |
| configuration | for |
| |||||||||||
your |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| ||||
Configure | the |
|
| drive |
| as |
| a | Master | if | it | will | be | the | |||||||||||
only |
| device |
| connected | to |
| an | IDE | cable. | (This |
| is | the |
| preset | ||||||||||
configuration.) |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| ||||
Configure the |
|
| drive |
| as |
| a | Slave | if | it |
| will | be | the | |||||||||||
second | device | on |
| an | IDE |
| cable. | Be | sure | to | configure | the | other | ||||||||||||
device | as | a | Master. | In |
| some | cases, |
| a | hard |
| disk |
| drive | might | ||||||||||
require | a | Master |
| with |
| Slave | Present | jumper | setting | when | another | ||||||||||||||
device on the same cable |
| is |
| configured | as | a | Slave. | For | further | ||||||||||||||||
information | on | setting | configuration | jumpers |
| on | other | devices, |
|
| |||||||||||||||
refer |
| to | the | documentation |
| that | comes | with | your | computer | system | ||||||||||||||
or | with | the | device. |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| |||||
Some |
| special | ATA | cables | with | two | wires | ||||||||||||||||||
reversed | in |
| the |
| device | connectors | so | that | the | drives | can | be | |||||||||||||
configured | by |
| the | cable |
| instead |
| of |
| by | jumper | position. | Use the | ||||||||||||
Cable |
| Select |
| position | only |
| for systems equipped with these |
| |||||||||||||||||
special |
| cables. | See | the |
| documentation |
| that | came | with |
| your |
|
| |||||||||||
computer | to |
| determine | if |
| your | ATA | adapter | requires | that | you |
| |||||||||||||
place |
| the | jumpers | in | the |
| Cable | Select | position. |
|
|
|
|
|
| ||||||||||
If | you | place | the | jumpers |
| in | the | Cable |
| Select | position, |
| the | IDE | |||||||||||
cable |
| automatically | assigns |
| the |
| Master | and | Slave | settings | based | ||||||||||||||
on | the | position |
| of | the |
| drive | on |
| the |
| cable. | You | must | use | the | |||||||||
Cable |
| Select |
| setting | for |
| this | cabling | system | whether |
| the |
| ||||||||||||
only | device | or | the |
| second |
| device |
| |||||||||||||||||
connected | to |
| the | cable. | The | drive |
| closest | to |
| the |
| IDE | controller is | |||||||||||
automatically |
| the |
| Master |
| drive. | Any | other | devices | on | the | IDE | |||||||||||||
cable |
| must | also |
| be | set |
| to |
| Cable | Select. |
|
|
|
|
|
|
|
|
Step | 4. |
| Mounting | the | drive | in | the |
| bay |
|
|
|
|
|
| |||||
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| |||||
Attention: |
| Be | sure |
| to | use | the |
| M3 | x | 5 | mm | mounting screws | that |
| |||||
come | with |
| the | option | package. | You |
| might |
| damage the | drive | if |
|
| ||||||
you | use |
| mounting | screws | that | are |
| too | long. |
|
|
|
|
|
| |||||
|
|
|
|
|
|
|
|
|
| |||||||||||
You | can mount the | drive |
| horizontally | or | vertically | in |
|
| |||||||||||
the | computer. | If | you | mount | the | drive | vertically, | you |
| must | secure | any | ||||||||
CDs | you | place | into the | drive | before |
| closing | the | drive | tray, or | the drive | |||||||||
will | not | be | able | to | read | from | the |
| CD | properly. | For |
| further | instructions | ||||||
on securing |
| your CDs | in | a | vertically | mounted | drive, | go | to | page |
|
1.Slide the drive into the bay. Your computer might require unique installation procedures for storage devices. Refer to the
documentation that comes with your computer for further instructions on installing storage devices.
2. | Align | the | screw holes | with the threaded | holes | in | the | ||||||
| drive | housing | or | mounting | bracket. |
|
|
|
|
|
| ||
3. | Loosely | hand | thread | the | screws | in | the | screw | holes | to | check | the | |
| alignment | of | the | screws | with | the | screw | holes. | Usually | two |
| ||
| screws | are | used | on | each | side. | If | the | screws | are | correctly | aligned | |
| with | the | screw | holes, | tighten | them | to | secure | the | driveDo .not |
|
overtighten.
Part 1: Quick installation guide