6. | Load a | data | CD | into | the | CD | tray; | then | wait | until | the | busy |
| indicator | is | not | lit. |
|
|
|
|
|
|
|
|
7. | Attempt | to | read | from | the | CD | by typingdir x: | where | x is | the | ||
| drive | letter | assigned | after | the | MSCDEX | message. |
|
If | the | computer | is |
| able | to | read | the | CD, | a | conflict | probably | ||||
exists | between |
| the | device | drivers | loaded in the |
|
| ||||||||
CONFIG.SYS | or | AUTOEXEC.BAT files. | You | need | to |
|
|
| ||||||||
resolve | this | device |
| conflict. | You | might have to set some | ||||||||||
configuration | parameters | for | your | installation; | refer | to |
|
| ||||||||
Appendix C, | “Customizing | device driver | configuration |
|
|
| ||||||||||
settings” | on | page | for | more | information. |
|
|
|
| |||||||
If | you | are | unable |
| to | access | the | CD, | you | might | have | a | ||||
hardware | problem. | If | you | are | unable | to |
| read | from | the | CD | or | ||||
a | drive | letter |
| is |
| not | assigned | by |
| MSCDEX, | go to the next | |||||
step. |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
13.Restart the computer.
14.Attempt to read from the CD by typingdir C:. (The
drive | C | because it is | the | only | device | |||||||||
connected | to | the | IDE | port.) |
|
|
|
|
|
|
|
| ||
If | the |
| computer | is | able | to | read | the | CD, | a | conflict | probably | ||
exists |
| with | one | of | the | devices | that | was | installed | on your | ||||
computer. |
| You | need | to | resolve | this | device | driver | conflict. | |||||
Check | the | configuration | jumper | settings | for | the | other | devices | ||||||
or | refer |
| to | your | device | documentation. |
|
|
|
|
| |||
If | you |
| are | unable | to | access | the | CD, | you | might | have a | |||
hardware | problem. If the | drive | still | does | not | |||||||||
read | from |
| the data CD, the | drive | might | be | ||||||||
defective. | Go | to | Appendix | E, | “Help | and | service |
|
| |||||
information” |
| on | page |
|
|
|
|
|
|
|
|
8. Turn off the computer, | unplug | the | cables | from | the | electrical |
| The | CD | cannot | be | read. |
|
|
|
|
| ||||||||||||
outlets | for | your | computer | and |
| all | attached devices, | and | remove | Take | the | following | actions: |
|
|
|
|
| |||||||||||
the | computer | cover. |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| |||||||||||
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| |||||||
9. | Disconnect | the |
| IDE | and | power | cable | for | all | IDE devices |
| except | 1. The | CD | might | be | dirty; |
| clean | it as | described in | “Caring for a | |||||||
|
|
| CD” | on | page |
|
|
|
|
|
| ||||||||||||||||||
the | drive. |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| |||||||||||
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| ||||||||
10. | Configure the | drive | as | a | master | and | connect |
| it to | 2. | The | CD | might | be | defective; | try | another | CD. |
| ||||||||||
|
|
|
|
|
|
|
|
|
|
|
|
| |||||||||||||||||
the | last | IDE |
| connector | on | the | primary | IDE | port. |
|
|
| 3. | The | CD | is | not | or | High | Sierra | Group (HSG) | compatible. | |||||||
11. | Reinstall | the |
| computer | cover. | Reconnect all devices; then plug |
| Check | with | your | place of | purchase. |
|
| |||||||||||||||
|
|
|
|
|
|
|
|
|
|
|
|
| |||||||||||||||||
the | power | cords | into electrical | outlets. |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| |||||||||
12. | Place | the | System | Diskette | in | the | diskette | drive | and | a | data CD in |
|
|
|
|
|
|
|
|
|
|
| |||||||
the | drive. |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| ||||||
| IBM | 2X/4X/24X | Internal | IDE | Option Kit |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|