Manuals / IBM / Computer Equipment / Switch

IBM AA-RWF3A-TE manual Replacing an SFP

Models: AA-RWF3A-TE

1 159

Download 159 pages 29.86 Kb

Page 110

Replacing an SFP

7.Install the new Power Supply/Fan Assembly Unit in the chassis:

a.Orient the Power Supply/Fan Assembly Unit as shown in Figure 38, with the captive screw on the right.

25276a

Figure 38 Inserting the Power Supply/Fan Assembly Unit in the 4/32B SAN Switch

b.Gently push the power supply into the chassis until it is seated.

CAUTION:

Do not force the installation. Verify that the unit is oriented correctly before continuing.

c.Secure the Power Supply/Fan Assembly Unit to the chassis by screwing in the captive screw.

8.Plug the power cord in to the Power Supply/Fan Assembly Unit and press the AC power switch to “I” to turn it on.

9.Fasten the power cord in place by pulling the power cord retainer down over the power cord plug.

10.Verify that the LED on the new Power Supply/Fan Assembly Unit displays a steady green light while the switch is operating. If the LED is not green, ensure that the Power Supply/Fan Assembly Unit is firmly seated.

11.Optionally, type psShow at the command line prompt to display Power Supply/Fan Assembly Unit status. Fabric OS identifies the Power Supply/Fan Assembly Unit in the 4/32B SAN Switch from left to right as PS1 and PS2 respectively. See Figure 38.

Replacing an SFP

To remove a faulty SFP transceiver:

1.Press and hold the cable release.

2.Remove the cable from the transceiver.

3.Pull the bale (wire handle) to release the transceiver.

4.Grasp the transceiver by the bale and gently, but firmly, pull it out of the port.

110	Installing field-replaceable units

Image 110

IBM AA-RWF3A-TE manual Replacing an SFP

Contents

HP StorageWorks SAN Switch installation guide Part number AA-RWF3A-TE Fifth edition MayLegal and notice information 1 Overview ContentsAbout this guide 2 Installing and configuring SAN Switches 3 Managing SAN Switches4 Installing field-replaceable units A Regulatory compliance and safetyC SAN Switch technical specifications B Electrostatic dischargeSupported HBAs GlossaryIndex Figures Tables Page Intended audience Document conventions and symbols, page HP technical support, pageAbout this guide Related documentationDocument conventions and symbols Table 1 Document conventionsHP technical support Rack stabilityFor the name of your nearest HP-authorized reseller HP authorized resellerHelpful web sites In the United States, callEnabling EPorts on the 4/8 SAN Switch , page 4/8 and 4/16 SAN Switch models4/8 and 4/16 SAN Switch models, page 4/32 SAN Switch models, page 4/64 SAN Switch models, page4/8 and 4/16 SAN Switch features 4/8 and 4/16 SAN Switch port side 4/8 and 4/16 SAN Switch chassisActivating additional 4/8 and 4/16 SAN Switch ports 4/8 and 4/16 SAN Switch nonport sideEnabling EPorts on the 4/8 SAN Switch SAN Switch licensing 4/32 SAN Switch chassis 4/32 SAN Switch models4/32 SAN Switch features To add ports, see Activating additional 4/32 SAN Switch ports on pageFC ports 4/32 SAN Switch port sideFigure 2 4/32 SAN Switch port side scale 1/8 =Figure 3 4/32 SAN Switch nonport side Activating additional 4/32 and 4/32B SAN Switch ports4/32 SAN Switch nonport side a. Log in to the 4/32 SAN Switch as admin To add ports, see Activating additional 4/64 SAN Switch ports on page 4/64 SAN Switch models4/64 SAN Switch features 4/64 SAN Switch chassis 4/64 SAN Switch port sideFigure 4 4/64 SAN Switch port side Figure 5 4/64 SAN Switch port numbering 4/64 SAN Switch port numbering4/64 SAN Switch nonport side 16 17Activating additional 4/64 SAN Switch ports Figure 6 4/64 SAN Switch nonport side4/32B SAN Switch chassis 4/32B SAN Switch models4/32B SAN Switch features 25271a 4/32B SAN Switch port sideFigure 7 4/32B SAN Switch port side Locating 4/32B SAN Switch FC ports SAN Switch ISL Trunking groupsActivating additional 4/32B SAN Switch ports Figure 8 4/32B SAN Switch FC portsOptional SAN Switch features SAN Switch optional port licenses and hardware Table 2 Optional port licenses and hardware kits34Overview Shipping carton contents, page 2 Installing and configuring SAN SwitchesShipping carton contents Installation and safety considerations, pageNumber Table 3 SAN Switch shipping carton checklistTable 3 identifies the carton contents included with your SAN Switch One HP StorageWorks 4/16 SAN Switch NumberDescription One HP StorageWorks 4/32 SAN SwitchEnvironmental considerations Installation and safety considerationsElectrical considerations Rack specifications Cooling considerationsInstalling the switch as a stand-alone device Installing the switch using the SAN Switch Rack Mount Kit Table 4 SAN Switch Rack Mount Kit hardware DescriptionFigure 10 Installing the rear mounting brackets HP 10000 series racks Figure 11 Installing the rear mounting brackets HP System/e RackFigure 12 Installing the outer rails HP 10000 series racks Figure 13 Assembling the outer rails HP 10000 series racks Figure 14 Assembling the outer rails HP System/e Rack Table 5 Number of screws required to assemble the inner rails6. Identify the screw holes to be used on the inner rails designed for the switch 2. SAN Switch Figure 15 Attaching the inner rails to the 4/8 or 4/16 SAN SwitchFigure 16 Attaching the inner rails to the 4/32 or 4/64 SAN Switch 1. PlenumInstalling the Plenum if required Securing the switch to the outer rails Figure 17 Attaching the Plenum to the 4/8 or 4/16 SAN SwitchFigure 19 Securing the switch in an HP System/e rack Cabling and configuring the SAN Switch Recommendations for cable management7. Install the SFP transceivers on page 8. Connect the cables on page Connecting the SAN Switch to the fabric3. Apply power to the switch and log in on page 9. Verify the configuration on page0014b Figure 20 Connecting the serial cableInstalling and configuring SAN Switches IOIOI3. Close any serial communication programs running on the workstation Apply power to the switch and log in Figure 21 Connecting the power cordSet the IP address Modify the FC domain ID optional Figure 22 Connecting the Ethernet cableCreate an Ethernet connection Installing and configuring SAN SwitchesInstall the SFP transceivers Connect the cables Verify the configurationBack up the configuration switch admin date Fri May 5 215000 UTC 1989 switchadmin Set the switch date and timeSynchronize the local time with an external source switchadmin date “0624165203” Tue Jun 24 165230 UTC 2003 switchadminswitchadmin tsclockserver 132.163.135.131 switchadmin Set the time zoneswitchadmin tsclockserver LOCL tstimezone parameter Table 6 Time zone command valuesLocal time Installing and configuring SAN Switches Managing SAN Switches from a single management station, page 3 Managing SAN SwitchesPowering on and off, page SAN Switch management features, page Interpreting LED activity, page 4/8 and 4/16 SAN Switch LEDs, page4/32, 4/32B and 4/64 SAN Switch models Powering on and off4/8 and 4/16 SAN Switch models Table 7 Management tools SAN Switch management featuresManaging SAN Switches from a single management station 2nd switch Table 8 Example of a set of gateway addresses1st switch 3rd switchInterpreting LED activity 4/8 and 4/16 SAN Switch LEDsFigure 23 4/8 and 4/16 SAN Switch LED locations Table 9 4/8 and 4/16 SAN Switch LED patterns 4/8 and 4/16 SAN Switch LED patternsPower Status LED patterns 4/8 and 4/16 SAN Switch system Status LED patterns Table 10 System status LED patterns during normal operation4/8 and 4/16 SAN Switch port LED patterns Table 11 Port LED patterns during normal operationHardware status LED nameLED color Recommended actionTable 12 Ethernet LED patterns 4/32 SAN Switch port side LEDs4/8 and 4/16 SAN Switch Ethernet LED patterns IOIOI Figure 24 4/32 SAN Switch port side LEDsBottom port LEDs 4 through scale 5/16 =LED name Table 13 4/32 SAN Switch port side LED patternsTable 13 describes the 4/32 SAN Switch port side LEDs LED colorLED color portenable commandLED name Hardware status2. Power Supply 1 Status LED 4/32 SAN Switch nonport side LEDsFigure 25 4/32 SAN Switch nonport side LEDs Managing SAN Switches4/64 SAN Switch port side LEDs Table 14 4/32 SAN Switch nonport side LED patternsFigure 26 4/64 SAN Switch port side LEDs IOIOILED color Table 15 4/64 SAN Switch port side LED patternsLED name Hardware status4/64 SAN Switch nonport side LEDs portenable commandFan assembly Figure 27 4/64 SAN Switch nonport side LEDs1. Power Supply 2 Status LED Fan assemblyHardware status LED nameLED color Recommended actionTable 17 4/32B SAN Switch LED patterns during normal operation 4/32B SAN Switch LEDsFigure 28 4/32B SAN Switch port side LEDs Hardware status LED nameLED color Recommended actionLED color portEnable commandLED name Hardware statusPOST POST and boot specificationsBoot 4/32 SAN Switch port side LEDs on page Diagnostic tests4/8 and 4/16 SAN Switch LED patterns on page 4/32 SAN Switch nonport side LEDs on pageManaging SAN Switches Replacing the SAN Switch 4/32 power supply, page 4 Installing field-replaceable unitsReplacing the 4/32 SAN Switch power supply Replacing the 4/32 SAN Switch fan assembly, pageFigure 29 4/32 SAN Switch power supplies on the nonport side Installing field-replaceable unitsTable 18 4/32 SAN Switch Power Supply Status LEDs Items requiredProcedure Figure 30 Installing the power supply in a 4/32 SAN SwitchDo not force the installation. If the power supply does not slide in easily, make sure that it is oriented correctly before continuing Replacing the 4/32 SAN Switch fan assembly Figure 31 4/32 SAN Switch fan assemblies on the nonport sideFan assembly is not receiving power Table 19 4/32 SAN Switch Fan Status LED behaviorProcedure Verify that the fan assembly is seated in theFigure 32 Installing the fan assembly in a 4/32 SAN Switch 1. Fan assemblyReplacing the 4/64 SAN Switch power supply Figure 33 4/64 SAN Switch power supplies on the nonport sideItems required New power supply Phillips #1 screwdriverInstalling field-replaceable units Procedure 3/8 = Figure 34 Installing the power supply in the 4/64 SAN SwitchScale Replacing the 4/64 SAN Switch fan assembly Figure 35 4/64 SAN Switch fan assemblies on the nonport sideItems required Table 20 Fan Status LEDsProcedure Figure 36 Inserting the fan assembly in a 4/64 SAN Switch Scale 3/8 =Figure 37 4/32B SAN Switch Power Supply/Fan Assembly Unit Replacing the 4/32B SAN Switch Power Supply/Fan Assembly UnitPower Supply/Fan Assembly overview Table 21 4/32B SAN Switch power supply/fan assembly unit status LED Fan 1 is OK, speed is 7105 RPM Fan 2 is OK, speed is 7258 RPM How to determine to replace the Power Supply/Fan Assembly UnitPower Supply #1 is OK Power Supply #2 is OK Items required Procedure4/32B SAN Switch New Power Supply/Fan Assembly Unit Replacing an SFP 5. Repeat this procedure for the remaining ports, as required. To install a replacement SFP IOIOI Figure 39 Installing the SFPInstalling field-replaceable units IOIOIFederal Communications Commission notice for Class A equipment A Regulatory compliance and safetyRegulatory compliance Laser device Laser safety warningRegulatory compliance identification numbers ModificationsCertification and classification information International notices and statementsCanadian notice avis Canadien Laser product labelEuropean Union notice BSMI noticeJapanese notice Korean notices SAN Switch installation guideSafety Battery replacement noticeJapanese power cord statement Taiwan battery recycling noticePower cords Dutch notice Waste Electrical and Electronic Equipment directiveEnglish notice Czechoslovakian notice Estonian noticeFinnish notice French noticeGerman notice Greek noticeHungarian notice Italian noticeLatvian notice Lithuanian noticePolish notice Portuguese noticeSlovakian notice Slovenian noticeSpanish notice Swedish noticeB Electrostatic discharge How to prevent electrostatic dischargeHow to prevent electrostatic discharge Grounding methods Grounding methodsElectrostatic discharge Data transmission ranges FC port specifications C SAN Switch technical specificationsGeneral specifications Weight and physical dimensions Serial port specifications Power supply specifications MemoryGeneral specifications Table 22 General specificationsDescription SpecificationLess than 2 μsec with no contention destination port is free Complies with FC-SW-2 RevFacility requirements Weight and physical dimensionsTable 23 SAN Switch physical dimensions Table 24 Facility requirementsType RequirementsEnvironmental requirements Table 25 Environmental requirementsCable size microns Data transmission rangesPort speed Short wavelengthCable size Table 27 Laser data transmission ranges for the 4/32 SAN SwitchPort speed Short wavelengthCable size Table 28 Laser data transmission ranges for the 4/64 SAN SwitchPort speed Short wavelength4/32 and 4/64 SAN Switch FC port specifications FC port specifications4/8 and 4/16 SAN Switch FC port specifications Table 29 Laser data transmission ranges for the 4/32B SAN SwitchSerial port specifications 4/32B SAN Switch FC port specificationsTable 30 Cabling pinouts Power supply specifications Table 31 Power supply specificationsTable 34 4/32B SAN Switch memory specifications Table 32 4/8 and 4/16 SAN Switch memory specificationsTable 33 4/32 and 4/64 SAN Switch memory specifications MemorySupported HBAs SAN Switch installation guideSAN Switch technical specifications arbitrated loop, point-to-point, topology Glossaryattachment. See also public device, public loop configuration configurationtrunking, UPort assigned manually. The domain ID for an HP switch can be anyfabric See also PLOGIcontrol frames and data frames. See also packet See also non-participating mode initialization. See also defined zone configurationor non-participating mode Eport, Fport, UPortLoop initialization primitive. The signal that begins initialization See also ISL trunkingSNS. See also SNS also phantom address also LPort, ???phantom device communicating entities. See also buffer-to-buffer flow controlpublic loop arbitrated loopthe fabric. See also Eport, Fport, GPort be called a management station or hostzone, but are not visible to any outside the zone. See also defined zone configuration, enabled zone configuration 156Glossary Index 4/32, 20 4/32B, 29 4/64