Manuals / IBM / Computer Equipment / Switch

IBM AA-RWF3A-TE manual LED name, LED color, Hardware status, Recommended action

Models: AA-RWF3A-TE

1 159

Download 159 pages 29.86 Kb

Page 84

Table 16 4/64 SAN Switch nonport side LED patterns during normal operation

LED name	LED color	Hardware status	Recommended action

Power Supply	No light	Power supply is not receiving	Verify that the power supply is on
Status		power or power is off.	and seated and the power cord is
			connected to a functioning power
			source.

	Steady green	Power supply is operating	No action required.
		normally.

	Steady	Power supply fault for one of the	Try the following:
	amber (for	following reasons:	Check the power cable connection.
	more than 5	Power cable is disconnected.	Check the power cable connection.
	more than 5		Verify that the power supply is
	seconds)		Verify that the power supply is
	seconds)	Power supply is off. Power supply	powered on.
		Power supply is off. Power supply	powered on.
		has failed.	Replace the power supply.
		During POST, the LED displays	Replace the power supply.
		During POST, the LED displays
		amber.

Fan Status	No light	Fan assembly is not receiving	Verify that the fan assembly is
		power.	seated in the switch.
			Verify that the switch is powered
			on.

	Steady green	Fan assembly is operating	No action required.
		normally.

	Steady	One or more of the fans in the fan	Verify that the fan FRU is enabled
	amber (for	assembly failed or the fan FRU	(use fanenable command). If
	more than 5	was disabled by the user.	the fan FRU is enabled, the FRU is
	seconds)		faulty and should be replaced.

84	Managing SAN Switches

Image 84

IBM AA-RWF3A-TE manual LED name, LED color, Hardware status, Recommended action

Contents

HP StorageWorks SAN Switch installation guide Part number AA-RWF3A-TE Fifth edition MayLegal and notice information Contents About this guide1 Overview 2 Installing and configuring SAN Switches 3 Managing SAN Switches4 Installing field-replaceable units A Regulatory compliance and safetyC SAN Switch technical specifications B Electrostatic dischargeGlossary IndexSupported HBAs Figures Tables Page Document conventions and symbols, page HP technical support, page About this guideIntended audience Related documentationDocument conventions and symbols Table 1 Document conventionsHP technical support Rack stabilityHP authorized reseller Helpful web sitesFor the name of your nearest HP-authorized reseller In the United States, call4/8 and 4/16 SAN Switch models 4/8 and 4/16 SAN Switch models, pageEnabling EPorts on the 4/8 SAN Switch , page 4/32 SAN Switch models, page 4/64 SAN Switch models, page4/8 and 4/16 SAN Switch features 4/8 and 4/16 SAN Switch chassis Activating additional 4/8 and 4/16 SAN Switch ports4/8 and 4/16 SAN Switch port side 4/8 and 4/16 SAN Switch nonport sideEnabling EPorts on the 4/8 SAN Switch SAN Switch licensing 4/32 SAN Switch models 4/32 SAN Switch features4/32 SAN Switch chassis To add ports, see Activating additional 4/32 SAN Switch ports on page4/32 SAN Switch port side Figure 2 4/32 SAN Switch port sideFC ports scale 1/8 =Activating additional 4/32 and 4/32B SAN Switch ports 4/32 SAN Switch nonport sideFigure 3 4/32 SAN Switch nonport side a. Log in to the 4/32 SAN Switch as admin 4/64 SAN Switch models 4/64 SAN Switch featuresTo add ports, see Activating additional 4/64 SAN Switch ports on page 4/64 SAN Switch chassis 4/64 SAN Switch port sideFigure 4 4/64 SAN Switch port side 4/64 SAN Switch port numbering 4/64 SAN Switch nonport sideFigure 5 4/64 SAN Switch port numbering 16 17Activating additional 4/64 SAN Switch ports Figure 6 4/64 SAN Switch nonport side4/32B SAN Switch models 4/32B SAN Switch features4/32B SAN Switch chassis 4/32B SAN Switch port side Figure 7 4/32B SAN Switch port side25271a SAN Switch ISL Trunking groups Activating additional 4/32B SAN Switch portsLocating 4/32B SAN Switch FC ports Figure 8 4/32B SAN Switch FC portsOptional SAN Switch features SAN Switch optional port licenses and hardware Table 2 Optional port licenses and hardware kits34Overview 2 Installing and configuring SAN Switches Shipping carton contentsShipping carton contents, page Installation and safety considerations, pageTable 3 SAN Switch shipping carton checklist Table 3 identifies the carton contents included with your SAN SwitchNumber Number DescriptionOne HP StorageWorks 4/16 SAN Switch One HP StorageWorks 4/32 SAN SwitchInstallation and safety considerations Electrical considerationsEnvironmental considerations Rack specifications Cooling considerationsInstalling the switch as a stand-alone device Installing the switch using the SAN Switch Rack Mount Kit Table 4 SAN Switch Rack Mount Kit hardware DescriptionFigure 10 Installing the rear mounting brackets HP 10000 series racks Figure 11 Installing the rear mounting brackets HP System/e RackFigure 12 Installing the outer rails HP 10000 series racks Figure 13 Assembling the outer rails HP 10000 series racks Figure 14 Assembling the outer rails HP System/e Rack Table 5 Number of screws required to assemble the inner rails6. Identify the screw holes to be used on the inner rails designed for the switch Figure 15 Attaching the inner rails to the 4/8 or 4/16 SAN Switch Figure 16 Attaching the inner rails to the 4/32 or 4/64 SAN Switch2. SAN Switch 1. PlenumInstalling the Plenum if required Securing the switch to the outer rails Figure 17 Attaching the Plenum to the 4/8 or 4/16 SAN SwitchFigure 19 Securing the switch in an HP System/e rack Cabling and configuring the SAN Switch Recommendations for cable managementConnecting the SAN Switch to the fabric 3. Apply power to the switch and log in on page7. Install the SFP transceivers on page 8. Connect the cables on page 9. Verify the configuration on pageFigure 20 Connecting the serial cable Installing and configuring SAN Switches0014b IOIOI3. Close any serial communication programs running on the workstation Apply power to the switch and log in Figure 21 Connecting the power cordSet the IP address Figure 22 Connecting the Ethernet cable Create an Ethernet connectionModify the FC domain ID optional Installing and configuring SAN SwitchesInstall the SFP transceivers Verify the configuration Back up the configurationConnect the cables Set the switch date and time Synchronize the local time with an external sourceswitch admin date Fri May 5 215000 UTC 1989 switchadmin switchadmin date “0624165203” Tue Jun 24 165230 UTC 2003 switchadminSet the time zone switchadmin tsclockserver LOCLswitchadmin tsclockserver 132.163.135.131 switchadmin Table 6 Time zone command values Local timetstimezone parameter Installing and configuring SAN Switches 3 Managing SAN Switches Powering on and off, page SAN Switch management features, pageManaging SAN Switches from a single management station, page Interpreting LED activity, page 4/8 and 4/16 SAN Switch LEDs, pagePowering on and off 4/8 and 4/16 SAN Switch models4/32, 4/32B and 4/64 SAN Switch models SAN Switch management features Managing SAN Switches from a single management stationTable 7 Management tools Table 8 Example of a set of gateway addresses 1st switch2nd switch 3rd switch4/8 and 4/16 SAN Switch LEDs Figure 23 4/8 and 4/16 SAN Switch LED locationsInterpreting LED activity 4/8 and 4/16 SAN Switch LED patterns Power Status LED patternsTable 9 4/8 and 4/16 SAN Switch LED patterns 4/8 and 4/16 SAN Switch system Status LED patterns Table 10 System status LED patterns during normal operation4/8 and 4/16 SAN Switch port LED patterns Table 11 Port LED patterns during normal operationLED name LED colorHardware status Recommended action4/32 SAN Switch port side LEDs 4/8 and 4/16 SAN Switch Ethernet LED patternsTable 12 Ethernet LED patterns Figure 24 4/32 SAN Switch port side LEDs Bottom port LEDs 4 throughIOIOI scale 5/16 =Table 13 4/32 SAN Switch port side LED patterns Table 13 describes the 4/32 SAN Switch port side LEDsLED name LED colorportenable command LED nameLED color Hardware status4/32 SAN Switch nonport side LEDs Figure 25 4/32 SAN Switch nonport side LEDs2. Power Supply 1 Status LED Managing SAN Switches4/64 SAN Switch port side LEDs Table 14 4/32 SAN Switch nonport side LED patternsFigure 26 4/64 SAN Switch port side LEDs IOIOITable 15 4/64 SAN Switch port side LED patterns LED nameLED color Hardware status4/64 SAN Switch nonport side LEDs portenable commandFigure 27 4/64 SAN Switch nonport side LEDs 1. Power Supply 2 Status LEDFan assembly Fan assemblyLED name LED colorHardware status Recommended action4/32B SAN Switch LEDs Figure 28 4/32B SAN Switch port side LEDsTable 17 4/32B SAN Switch LED patterns during normal operation LED name LED colorHardware status Recommended actionportEnable command LED nameLED color Hardware statusPOST and boot specifications BootPOST Diagnostic tests 4/8 and 4/16 SAN Switch LED patterns on page4/32 SAN Switch port side LEDs on page 4/32 SAN Switch nonport side LEDs on pageManaging SAN Switches 4 Installing field-replaceable units Replacing the 4/32 SAN Switch power supplyReplacing the SAN Switch 4/32 power supply, page Replacing the 4/32 SAN Switch fan assembly, pageFigure 29 4/32 SAN Switch power supplies on the nonport side Installing field-replaceable unitsTable 18 4/32 SAN Switch Power Supply Status LEDs Items requiredProcedure Figure 30 Installing the power supply in a 4/32 SAN SwitchDo not force the installation. If the power supply does not slide in easily, make sure that it is oriented correctly before continuing Replacing the 4/32 SAN Switch fan assembly Figure 31 4/32 SAN Switch fan assemblies on the nonport sideTable 19 4/32 SAN Switch Fan Status LED behavior ProcedureFan assembly is not receiving power Verify that the fan assembly is seated in theFigure 32 Installing the fan assembly in a 4/32 SAN Switch 1. Fan assemblyReplacing the 4/64 SAN Switch power supply Figure 33 4/64 SAN Switch power supplies on the nonport sideNew power supply Phillips #1 screwdriver Installing field-replaceable unitsItems required Procedure Figure 34 Installing the power supply in the 4/64 SAN Switch Scale3/8 = Replacing the 4/64 SAN Switch fan assembly Figure 35 4/64 SAN Switch fan assemblies on the nonport sideTable 20 Fan Status LEDs ProcedureItems required Figure 36 Inserting the fan assembly in a 4/64 SAN Switch Scale 3/8 =Replacing the 4/32B SAN Switch Power Supply/Fan Assembly Unit Power Supply/Fan Assembly overviewFigure 37 4/32B SAN Switch Power Supply/Fan Assembly Unit Table 21 4/32B SAN Switch power supply/fan assembly unit status LED How to determine to replace the Power Supply/Fan Assembly Unit Power Supply #1 is OK Power Supply #2 is OKFan 1 is OK, speed is 7105 RPM Fan 2 is OK, speed is 7258 RPM Procedure 4/32B SAN Switch New Power Supply/Fan Assembly UnitItems required Replacing an SFP 5. Repeat this procedure for the remaining ports, as required. To install a replacement SFP Figure 39 Installing the SFP Installing field-replaceable unitsIOIOI IOIOIA Regulatory compliance and safety Regulatory complianceFederal Communications Commission notice for Class A equipment Laser safety warning Regulatory compliance identification numbersLaser device ModificationsInternational notices and statements Canadian notice avis CanadienCertification and classification information Laser product labelEuropean Union notice BSMI noticeJapanese notice Korean notices SAN Switch installation guideSafety Battery replacement noticeTaiwan battery recycling notice Power cordsJapanese power cord statement Waste Electrical and Electronic Equipment directive English noticeDutch notice Czechoslovakian notice Estonian noticeFinnish notice French noticeGerman notice Greek noticeHungarian notice Italian noticeLatvian notice Lithuanian noticePolish notice Portuguese noticeSlovakian notice Slovenian noticeSpanish notice Swedish noticeHow to prevent electrostatic discharge How to prevent electrostatic discharge Grounding methodsB Electrostatic discharge Grounding methodsElectrostatic discharge C SAN Switch technical specifications General specifications Weight and physical dimensionsData transmission ranges FC port specifications Serial port specifications Power supply specifications MemoryGeneral specifications Table 22 General specificationsSpecification Less than 2 μsec with no contention destination port is freeDescription Complies with FC-SW-2 RevWeight and physical dimensions Table 23 SAN Switch physical dimensionsFacility requirements Table 24 Facility requirementsType RequirementsEnvironmental requirements Table 25 Environmental requirementsData transmission ranges Port speedCable size microns Short wavelengthTable 27 Laser data transmission ranges for the 4/32 SAN Switch Port speedCable size Short wavelengthTable 28 Laser data transmission ranges for the 4/64 SAN Switch Port speedCable size Short wavelengthFC port specifications 4/8 and 4/16 SAN Switch FC port specifications4/32 and 4/64 SAN Switch FC port specifications Table 29 Laser data transmission ranges for the 4/32B SAN SwitchSerial port specifications 4/32B SAN Switch FC port specificationsTable 30 Cabling pinouts Power supply specifications Table 31 Power supply specificationsTable 32 4/8 and 4/16 SAN Switch memory specifications Table 33 4/32 and 4/64 SAN Switch memory specificationsTable 34 4/32B SAN Switch memory specifications MemorySupported HBAs SAN Switch installation guideSAN Switch technical specifications Glossary attachment. See also public device, public looparbitrated loop, point-to-point, topology configuration trunking, UPortconfiguration assigned manually. The domain ID for an HP switch can be anySee also PLOGI control frames and data frames. See also packetfabric initialization. See also defined zone configuration or non-participating modeSee also non-participating mode Eport, Fport, UPortSee also ISL trunking SNS. See also SNSLoop initialization primitive. The signal that begins initialization also LPort, ??? phantom devicealso phantom address communicating entities. See also buffer-to-buffer flow controlpublic loop arbitrated loopthe fabric. See also Eport, Fport, GPort be called a management station or hostzone, but are not visible to any outside the zone. See also defined zone configuration, enabled zone configuration 156Glossary Index 4/32, 20 4/32B, 29 4/64