Manuals / Invacare / Personal Care / Mobility Scooter

Invacare 9000 XDT Storing/Replacing The Spreader Bar, Storing Figure, Replacing Figure, Section

Models: 9000 XDT 9000 Series

1 60

Download 60 pages 56.17 Kb

Page 48

STORING/REPLACING THE SPREADER BAR

FIGURE 6 - REPLACING THE

SPREADER BAR

SECTION 9

RECLINER

STORING/REPLACING THE SPREADER BAR

RECLINER

STORING (FIGURE 5)

NOTE: The 9000XT RECLINER is folded for either storage or transporting. One side of the spreader bar must be removed and placed in a vertical position along side the recliner tube.

Removing From The Stored Position.

1.Rotate the end of the spreader bar 90o toward the opposite side frame.

2.Install threaded end of locking knob into locknut located on the opposite side frame. Securely tighten both knobs.

REAR VIEW OF 9000XT RECLINER


	Locking
	Knob		Side
			Side
			Frame
Spreader
	Bar
Recliner		Locking	Threaded
	Tube	Locking	End
		Knob

FIGURE 5 - STORING THE

SPREADER BAR

Placing In The Stored Position.
1.	Remove one (1) locking knob from the
	spreader bar.	Locking
2.	Loosen the remaining locking knob on	Knobs
2.	Loosen the remaining locking knob on
	the spreader bar.
2.	Rotate detached end of the spreader
	bar 90o down toward floor.

	REPLACING (FIGURE 6)
	1. Remove both locking knobs that	Side
	secure the spreader bar to the side	Side
	secure the spreader bar to the side	Frame
	frames.	Frame
	frames.

2.Remove existing spreader bar.

3.Secure NEW spreader bar to the side

frames with the existing locking knobs. Securely tighten.

Spreader

Bar

Side

Frame

9000 Series

48

Part No. 1056953

Image 48

Invacare 9000 XDT, 9000 XT, 9000 SL Storing/Replacing The Spreader Bar, Storing Figure, Replacing Figure, Section, Recliner

Contents

Owners Operator And Maintenance Manual 9000 SERIES9000 SL 9000 XT 9000 XDT 9000XT RECLINER DEALER THIS MANUAL MUST BE GIVEN TO THE USER OF THE WHEELCHAIRSAVE THESE INSTRUCTIONS 9000 SeriesTABLE OF CONTENTS CONTENTSCONTENTS SPECIFICATIONSCONTENTS CONTENTSLIMITED WARRANTY SECTION 7 - FRONT CASTERSSPECIAL NOTES SPECIAL NOTESWHEELCHAIR USER SPECIAL NOTESLABEL LOCATIONS LOCK ADJUSTMENTSEXCEPT non-adjustable settingSPECIFICATIONS SPECIFICATIONSSPECIFICATIONS 9000 SLSPECIFICATIONS SPECIFICATIONSSPECIFICATIONS 9000 XT RECLINERINFORMATION FOR HEALTHCARE PROFESSIONALS/ ASSISTANTS GENERAL GUIDELINESSECTION GENERAL GUIDELINESSTABILITY - ALL MODELS ANTI-TIPPERSGENERAL GUIDELINES SECTIONSTABILITY - RECLINER MODELS ONLY OPERATING INFORMATIONANTI-TIPPERS CONTINUED GENERAL GUIDELINESGENERAL GUIDELINES SECTIONGENERAL GUIDELINES WARNING CONTINUEDWEIGHT TRAINING WEIGHT LIMITATIONTIRE PRESSURE GENERAL GUIDELINESSAFETY/HANDLING OF WHEELCHAIRS STABILITY AND BALANCECOPING WITH EVERYDAY OBSTACLES A NOTE TO WHEELCHAIR ASSISTANTSPERCENTAGE OF WEIGHT DISTRIBUTION GENERAL GUIDELINESSECTION GENERAL GUIDELINESREACHING, LEANING AND BENDING - FORWARD REACHING, LEANING - BACKWARDSTIPPING GENERAL GUIDELINESGENERAL GUIDELINES SECTIONTipping - Curbs Method 1 - Wheelchair With Step Tubes Tipping - Curbs Method 2 - Wheelchair Without Step TubesSTAIRWAYS GENERAL GUIDELINESSECTION GENERAL GUIDELINESTRANSFERRING TO AND FROM OTHER SEATS UNFOLDING AND FOLDING THE WHEELCHAIRGENERAL GUIDELINES SECTIONGENERAL GUIDELINES SECTIONGENERAL GUIDELINES Folding Hammock or Sling Seat ModelsSAFETY INSPECTION CHECKLIST SAFETY INSPECTIONSAFETY INSPECTION Section 2 - Safety Inspection includes the followingTROUBLESHOOTING MAINTENANCEMAINTENANCE SAFETY PRECAUTIONS SUGGESTED MAINTENANCE PROCEDURESSAFETY INSPECTION SAFETY INSPECTIONSECTION NOTE Tire wear is excessive ifINSTALLING/REMOVING/USING THE FOOTREST/LEGREST FIGURE INSTALLINGUSING 1. Turn the swingaway footrest assemblyFOOTREST HEIGHT ADJUSTMENT FIGURE NOTE Lay the assembly on a flat surface to simplify this procedureFIGURE 2 - FOOTREST HEIGHT ADJUSTMENT IMPACT GUARDS/CALF STRAP FIGUREHEEL LOOP REPLACEMENT FIGURE REPLACEMENTFRONT RIGGINGS SECTION 3FRONT RIGGINGSRAISING/LOWERING THE ELEVATING LEGREST ASSEMBLY FIGURE FIGURE 5 - ADJUSTING THE ELEVATING LEGREST ASSEMBLYFRONT RIGGINGS SECTIONADJUSTING ARMREST HEIGHT FIGURE FIGURE 1 - ADJUSTING ARMRESTthe arm assembly SWING-BACK ARMS FIGURENOTE This procedure DOES NOT apply to 9000 SL wheelchairs REMOVING OR REPLACING ARMREST FIGUREARMREST PAD CLOTHING GUARDA. 9000XT with the adjustable angle back option ARMSSECTION ARMSREPLACING THE SEAT UPHOLSTERY FIGURE SEAT AND BACKSECTION FIGURE 1 - REPLACING THE SEAT UPHOLSTERYREPLACING THE BACK UPHOLSTERY SCREW ON BACK UPHOLSTERY - 9000 SL FIGURESLIP ON BACK UPHOLSTERY - 9000 XT/XDT FIGURE SECTIONADJUSTING THE BACK HEIGHT, BACK ANGLE OR SEAT DEPTH ADJUSTING THE SEAT WIDTHSEAT AND BACK SECTIONREMOVING/INSTALLING THE REAR WHEELS PERMANENT AXLESQUICK-RELEASE AXLES FIGURE WHEELSREARKeep locking pins clean DETAIL A - LOCKING PINS AND DETENT PINFIGURE 1 - REMOVING/INSTALLING THE REAR WHEELS QUICK-RELEASE AXLES REAR WHEELSREPLACING/REPAIRING REAR WHEEL TIRE/TUBE REPLACING REAR WHEEL HANDRIM FIGURESECTION REAR WHEELSADJUSTING THE QUICK-RELEASE AXLE FIGURE Keep locking pins cleanFIGURE 3 - ADJUSTING THE QUICK-RELEASE AXLE REAR WHEELSINSTALLING/REPLACING SIX OR EIGHT-INCH FRONT CASTERS AND FORKS FIGURE CASTERSFRONTSECTION FRONT CASTERSREPLACING/REPAIRING FRONT CASTER TIRE/TUBE FRONT CASTER MOUNTING ADJUSTMENTSFIGURE 1 - INSTALLING/REPLACING SIX OR EIGHT-INCH FRONT FRONT CASTERSINSTALLING/ADJUSTING THE ANTI-TIPPERS INSTALLING ANTI-TIPPERS FIGUREEnsure both anti-tippers are adjusted to the same mounting hole FIGURE 1 - INSTALLING THE ANTI-TIPPERSADJUSTING FIGURE FIGURE 2 - ADJUSTING THE ANTI-TIPPERSANTI-TIPPERS/WHEEL LOCKS SECTIONUSING/ADJUSTING THE PATIENT OPERATED WHEEL LOCKS USING THE PATIENT OPERATED WHEEL LOCKS FIGUREADJUSTING THE PATIENT OPERATED WHEEL LOCKS FIGURE FIGURE 3 - USING THE PATIENT OPERATED WHEEL LOCKSFIGURE 4 - ADJUSTING THE PATIENT OPERATED WHEEL LOCKS ANTI-TIPPERS/WHEEL LOCKSSECTION BOLT-ON WHEEL LOCKSRECLINER OPERATION FIGURE RECLINERSECTION RECLINERRECLINER SECTIONWARNING CONTINUED RECLINERNOTE To remove and install the bottom two REPLACING THE HEADREST PILLOW FIGUREREPLACING THE HEADREST/BACK UPHOLSTERY FIGURE HEADREST UPHOLSTERYADJUSTING HEADREST/BACK UPHOLSTERY TENSION FIGURE ADJUSTING THE SEAT DEPTHADJUSTING THE SEAT WIDTH FIGURE 4 - ADJUSTING HEADREST/BACK UPHOLSTERY TENSIONSTORING/REPLACING THE SPREADER BAR STORING FIGUREREPLACING FIGURE SECTIONINSTALLING THE ANTI-TIPPERS FIGURE FIGURE 15 - INSTALLING THE ANTI-TIPPERSRECLINER SECTIONREMOVING/INSTALLING THE REAR WHEELS FIGURE 8 - REMOVING INSTALLING THE REAR WHEELS WITH PATIENT OPERATEDFIGURE 9 - REMOVING INSTALLING THE REAR WHEELS WITH ATTENDANT WITH PATIENT OPERATED WHEEL LOCKS FIGUREUSING/ADJUSTING THE WHEEL LOCKS USING ATTENDANT OPERATED WHEEL LOCKS FIGUREADJUSTING ATTENDANT OPERATED WHEEL LOCKS FIGURE DISENGAGE FIGURE 10 - USING ATTENDANT OPERATED WHEEL LOCKSINSTALLING THE TELESCOPING I.V. ROD INSTALLING THE TELESCOPING I.V. ROD HOLDER FIGUREFIGURE 12 - INSTALLING THE TELESCOPING I.V. ROD HOLDER SECTIONINSTALLING THE TELESCOPING I.V. ROD SUPPORT TUBE FIGURE ADJUSTING THE TELESCOPING I.V. ROD FIGUREFIGURE 14 - INSTALLING/ADJUSTING THE TELESCOPING I.V. ROD RECLINERINSTALLING/CLEANING THE TELESCOPING I.V. ROD/ O2 HOLDERS FIGURE INSTALLINGFIGURE 1 - INSTALLING THE TELESCOPING I.V. ROD/O2 HOLDERS OPTIONSINSTALLING THE SOLID FOLDING SEAT FIGURE INSTALLING THE CRUTCH AND CANE CARRIER FIGURECLEANING FIGURE 2 - INSTALLING THE SOLID FOLDING SEATINSTALLING THE AMPUTEE BRACKET - SUPER HEMI MODELS ONLY FIGURE FIGURE 3 - INSTALLING THE CRUTCH AND CANE CARRIERFIGURE 4 - INSTALLING THE AMPUTEE BRACKET - SUPER HEMI MODELS ONLY SECTIONINSTALLING THE AMPUTEE BRACKET - ALL MODELS EXCEPT SUPER HEMI FIGURE 5 - INSTALLING THE AMPUTEE BRACKET - 9000SL/XT9000SL/XT FIGURE OPTIONSFIGURE 6 - INSTALLING THE AMPUTEE BRACKET - 9000XDT 9000XDT FIGUREOPTIONS SECTIONLIMITED WARRANTY WARRANTYWARRANTY Canada Invacare CorporationInvacare is a registered trademark of Invacare Corporation