Manuals / Invacare / Personal Care / Mobility Scooter

Invacare 9000 XDT Installing The Telescoping I.V. Rod Support Tube Figure, Recliner, Section

Models: 9000 XDT 9000 Series

1 60

Download 60 pages 56.17 Kb

Page 53

INSTALLING THE TELESCOPING I.V. ROD SUPPORT TUBE (FIGURE 14)

RECLINER		SECTION 9

INSTALLING THE TELESCOPING I.V. ROD SUPPORT TUBE (FIGURE 14)

NOTE: The I.V. rod holder must already be mounted to the side frame of the wheelchair.

1. Insert the I.V. rod support tube into the rear cylinder of the I.V. rod holder.

NOTE: When installing the I.V. rod support tube, ensure the adjustment knob is pointing out away from the wheelchair.

2.Turn the I.V. rod support tube until the holes in the I.V. rod support tube align with the holes in the rear cylinder of the I.V. rod holder.

3.Insert mounting screw through rear cylinder, large nylon washer, small nylon washer, steel washer, and into locknut. Securely tighten.

NOTE: The large nylon washer must be inserted into hole and pressed in so that it is flush with outside surface of rear cylinder.

4.Reinstall the rear wheel from the wheelchair. Refer to REMOVING/INSTALLING THE REAR WHEELS in this section of the manual.

5.Adjust I.V. rod to desired height. Refer to ADJUSTING THE TELESCOPING I.V. ROD in this section of the manual.

ADJUSTING THE TELESCOPING I.V. ROD (FIGURE 14)

RECLINER

1.Loosen adjustment knob.

2.Adjust I.V. Rod to desired height.

3.Securely tighten adjustment knob.

Adjustment Knob

Locknut

Steel Washer

Small Nylon Washer

Large Nylon Washer

Rear Cylinder

Mounting Screw

I.V. Rod

I.V. Rod Support Tube

I.V. Rod Holder

NOTE: Attaching hard- ware enlarged 3X scale for clarity.

FIGURE 14 - INSTALLING/ADJUSTING THE TELESCOPING I.V. ROD

SUPPORT TUBE

Part No. 1056953

53

9000 Series

Image 53

Invacare 9000 XDT manual Installing The Telescoping I.V. Rod Support Tube Figure, Adjusting The Telescoping I.V. Rod Figure

Contents

9000 SERIES Owners Operator And Maintenance Manual9000 SL 9000 XT 9000 XDT 9000XT RECLINER DEALER THIS MANUAL MUST BE GIVEN TO THE USER OF THE WHEELCHAIR9000 Series SAVE THESE INSTRUCTIONSCONTENTS TABLE OF CONTENTSCONTENTS SPECIFICATIONSCONTENTS CONTENTSLIMITED WARRANTY SECTION 7 - FRONT CASTERSSPECIAL NOTES SPECIAL NOTESWHEELCHAIR USER SPECIAL NOTESLOCK ADJUSTMENTS LABEL LOCATIONSEXCEPT non-adjustable settingSPECIFICATIONS SPECIFICATIONSSPECIFICATIONS 9000 SLSPECIFICATIONS SPECIFICATIONSSPECIFICATIONS 9000 XT RECLINERGENERAL GUIDELINES INFORMATION FOR HEALTHCARE PROFESSIONALS/ ASSISTANTSSECTION GENERAL GUIDELINESANTI-TIPPERS STABILITY - ALL MODELSGENERAL GUIDELINES SECTIONOPERATING INFORMATION STABILITY - RECLINER MODELS ONLYANTI-TIPPERS CONTINUED GENERAL GUIDELINESSECTION GENERAL GUIDELINESGENERAL GUIDELINES WARNING CONTINUEDWEIGHT LIMITATION WEIGHT TRAININGTIRE PRESSURE GENERAL GUIDELINESSTABILITY AND BALANCE SAFETY/HANDLING OF WHEELCHAIRSCOPING WITH EVERYDAY OBSTACLES A NOTE TO WHEELCHAIR ASSISTANTSGENERAL GUIDELINES PERCENTAGE OF WEIGHT DISTRIBUTIONSECTION GENERAL GUIDELINESREACHING, LEANING - BACKWARDS REACHING, LEANING AND BENDING - FORWARDTIPPING GENERAL GUIDELINESSECTION GENERAL GUIDELINESTipping - Curbs Method 1 - Wheelchair With Step Tubes Tipping - Curbs Method 2 - Wheelchair Without Step TubesGENERAL GUIDELINES STAIRWAYSSECTION GENERAL GUIDELINESUNFOLDING AND FOLDING THE WHEELCHAIR TRANSFERRING TO AND FROM OTHER SEATSGENERAL GUIDELINES SECTIONSECTION GENERAL GUIDELINESGENERAL GUIDELINES Folding Hammock or Sling Seat ModelsSAFETY INSPECTION SAFETY INSPECTION CHECKLISTSAFETY INSPECTION Section 2 - Safety Inspection includes the followingMAINTENANCE TROUBLESHOOTINGMAINTENANCE SAFETY PRECAUTIONS SUGGESTED MAINTENANCE PROCEDURESSAFETY INSPECTION SAFETY INSPECTIONSECTION NOTE Tire wear is excessive ifINSTALLING INSTALLING/REMOVING/USING THE FOOTREST/LEGREST FIGUREUSING 1. Turn the swingaway footrest assemblyNOTE Lay the assembly on a flat surface to simplify this procedure FOOTREST HEIGHT ADJUSTMENT FIGUREFIGURE 2 - FOOTREST HEIGHT ADJUSTMENT IMPACT GUARDS/CALF STRAP FIGUREREPLACEMENT HEEL LOOP REPLACEMENT FIGUREFRONT RIGGINGS SECTION 3FRONT RIGGINGSFIGURE 5 - ADJUSTING THE ELEVATING LEGREST ASSEMBLY RAISING/LOWERING THE ELEVATING LEGREST ASSEMBLY FIGUREFRONT RIGGINGS SECTIONFIGURE 1 - ADJUSTING ARMREST ADJUSTING ARMREST HEIGHT FIGUREthe arm assembly SWING-BACK ARMS FIGUREREMOVING OR REPLACING ARMREST FIGURE NOTE This procedure DOES NOT apply to 9000 SL wheelchairsARMREST PAD CLOTHING GUARDARMS A. 9000XT with the adjustable angle back optionSECTION ARMSSEAT AND BACK REPLACING THE SEAT UPHOLSTERY FIGURESECTION FIGURE 1 - REPLACING THE SEAT UPHOLSTERYSCREW ON BACK UPHOLSTERY - 9000 SL FIGURE REPLACING THE BACK UPHOLSTERYSLIP ON BACK UPHOLSTERY - 9000 XT/XDT FIGURE SECTIONADJUSTING THE SEAT WIDTH ADJUSTING THE BACK HEIGHT, BACK ANGLE OR SEAT DEPTHSEAT AND BACK SECTIONPERMANENT AXLES REMOVING/INSTALLING THE REAR WHEELSQUICK-RELEASE AXLES FIGURE WHEELSREARDETAIL A - LOCKING PINS AND DETENT PIN Keep locking pins cleanFIGURE 1 - REMOVING/INSTALLING THE REAR WHEELS QUICK-RELEASE AXLES REAR WHEELSREPLACING REAR WHEEL HANDRIM FIGURE REPLACING/REPAIRING REAR WHEEL TIRE/TUBESECTION REAR WHEELSKeep locking pins clean ADJUSTING THE QUICK-RELEASE AXLE FIGUREFIGURE 3 - ADJUSTING THE QUICK-RELEASE AXLE REAR WHEELSCASTERSFRONT INSTALLING/REPLACING SIX OR EIGHT-INCH FRONT CASTERS AND FORKS FIGURESECTION FRONT CASTERSFRONT CASTER MOUNTING ADJUSTMENTS REPLACING/REPAIRING FRONT CASTER TIRE/TUBEFIGURE 1 - INSTALLING/REPLACING SIX OR EIGHT-INCH FRONT FRONT CASTERSINSTALLING ANTI-TIPPERS FIGURE INSTALLING/ADJUSTING THE ANTI-TIPPERSEnsure both anti-tippers are adjusted to the same mounting hole FIGURE 1 - INSTALLING THE ANTI-TIPPERSFIGURE 2 - ADJUSTING THE ANTI-TIPPERS ADJUSTING FIGUREANTI-TIPPERS/WHEEL LOCKS SECTIONUSING THE PATIENT OPERATED WHEEL LOCKS FIGURE USING/ADJUSTING THE PATIENT OPERATED WHEEL LOCKSADJUSTING THE PATIENT OPERATED WHEEL LOCKS FIGURE FIGURE 3 - USING THE PATIENT OPERATED WHEEL LOCKSANTI-TIPPERS/WHEEL LOCKS FIGURE 4 - ADJUSTING THE PATIENT OPERATED WHEEL LOCKSSECTION BOLT-ON WHEEL LOCKSRECLINER RECLINER OPERATION FIGURESECTION RECLINERSECTION RECLINERWARNING CONTINUED RECLINERREPLACING THE HEADREST PILLOW FIGURE NOTE To remove and install the bottom twoREPLACING THE HEADREST/BACK UPHOLSTERY FIGURE HEADREST UPHOLSTERYADJUSTING THE SEAT DEPTH ADJUSTING HEADREST/BACK UPHOLSTERY TENSION FIGUREADJUSTING THE SEAT WIDTH FIGURE 4 - ADJUSTING HEADREST/BACK UPHOLSTERY TENSIONSTORING FIGURE STORING/REPLACING THE SPREADER BARREPLACING FIGURE SECTIONFIGURE 15 - INSTALLING THE ANTI-TIPPERS INSTALLING THE ANTI-TIPPERS FIGURERECLINER SECTIONFIGURE 8 - REMOVING INSTALLING THE REAR WHEELS WITH PATIENT OPERATED REMOVING/INSTALLING THE REAR WHEELSFIGURE 9 - REMOVING INSTALLING THE REAR WHEELS WITH ATTENDANT WITH PATIENT OPERATED WHEEL LOCKS FIGUREUSING ATTENDANT OPERATED WHEEL LOCKS FIGURE USING/ADJUSTING THE WHEEL LOCKSADJUSTING ATTENDANT OPERATED WHEEL LOCKS FIGURE DISENGAGE FIGURE 10 - USING ATTENDANT OPERATED WHEEL LOCKSINSTALLING THE TELESCOPING I.V. ROD HOLDER FIGURE INSTALLING THE TELESCOPING I.V. RODFIGURE 12 - INSTALLING THE TELESCOPING I.V. ROD HOLDER SECTIONADJUSTING THE TELESCOPING I.V. ROD FIGURE INSTALLING THE TELESCOPING I.V. ROD SUPPORT TUBE FIGUREFIGURE 14 - INSTALLING/ADJUSTING THE TELESCOPING I.V. ROD RECLINERINSTALLING INSTALLING/CLEANING THE TELESCOPING I.V. ROD/ O2 HOLDERS FIGUREFIGURE 1 - INSTALLING THE TELESCOPING I.V. ROD/O2 HOLDERS OPTIONSINSTALLING THE CRUTCH AND CANE CARRIER FIGURE INSTALLING THE SOLID FOLDING SEAT FIGURECLEANING FIGURE 2 - INSTALLING THE SOLID FOLDING SEATFIGURE 3 - INSTALLING THE CRUTCH AND CANE CARRIER INSTALLING THE AMPUTEE BRACKET - SUPER HEMI MODELS ONLY FIGUREFIGURE 4 - INSTALLING THE AMPUTEE BRACKET - SUPER HEMI MODELS ONLY SECTIONFIGURE 5 - INSTALLING THE AMPUTEE BRACKET - 9000SL/XT INSTALLING THE AMPUTEE BRACKET - ALL MODELS EXCEPT SUPER HEMI9000SL/XT FIGURE OPTIONS9000XDT FIGURE FIGURE 6 - INSTALLING THE AMPUTEE BRACKET - 9000XDTOPTIONS SECTIONWARRANTY LIMITED WARRANTYWARRANTY Invacare Corporation CanadaInvacare is a registered trademark of Invacare Corporation