Message Appears when Action | JVC LYT0002-0H6B, 0397MKV*UN*SN

38

EN

L

IS

T

O

F

E

R

R

O

R

ME

S

S

A

GES

Message

⬤ Appears when:

Page

⬛ Action:

COM port is not

⬤ Not connected to COM port set by JLIP Initialize.

18

available.

⬛ Check the COM port number and connector and

retry JLIP initialization.

Connected device

⬤ Connected devices are not turned on.

18,19

not found.

⬤ Selected COM port is not connected properly.

⬛ Make sure connection is proper and carry out JLIP

initialization. Then turn on this unit and the

connected devices.

Error — Transfer

⬤ Video unit is brought to STOP or ends playback

halted.

during automatic capture.

⬛ Check the auto capture setting.

⬤ Full image data (768 x 552 pixels) cannot be

—

captured if you start auto capture at the beginning

of the tape. Video capture stops if video playback

is stopped.

⬛ Start video capture 20 seconds after the start of the

recording.

28

⬤ Tape is too short to match the preset number of

images or there is a section of non-recorded tape.

⬛ Click "OK", check the tape length and re-enter the

number of images to be captured. Use a fully

recorded tape.

Image 38

JVC LYT0002-0H6B, 0397MKV*UN*SN manual Message Appears when Action

Contents

GV-DS1 Dear Customer It is recommended that you Do not place the Video Capture Docking Station AC Power Adapter/Charger How to handle a CD-ROMMaintenance Contents Jlip Player Software Additional OperationsSave Picture Getting Started Advanced Operations Troubleshooting Major Specifications IndexVideo Printer Operation GV-PT2 Internet homepage Major FeaturesBusiness presentations Video journal and postcards Jlip Control Facility Jlip Video Capture SoftwareVideo Capture Facility Data Sharing With Jlip Player Soft- ware Contro L S AN D Connec Tors Video output jack Outputs S-Video signal. Also Connections W hen Using JL IP Video Capture Software Input Operating Environment What is video capture software ?What is Jlip ? Connectable Devices Installation Procedure Windows Open & C Lose Bas ic Operatio n Proc edure Preparation HOW to Close the Program Click Exit from File in the menu bar. The program closes Initializing Jlip Select Transfer Rate. Normally select Select Units Control buttons Main Desktop WindowMenu bar Menu BAR Image display area Each pulldown menu is configured as follows EN H OW the Deskto P W ORK S VCR operation window 00012312F Image data flow Capturing Video Images Full image data is transferred to the computer Step by Step CaptureIndex image data is transferred to the computer Repeat steps 2 through 5 as required Program Capture EN V Ideo CA PtureAutomatic Capture Transfer Interval Capture Automatically Selecting a Picture Format Capture ModePicture Data Format Counter Value Change Counter ResetEN Addi Tional Oper AT Ions Modify Capture Point window appears You can change the Video Capture Unit’s ID number Delete Index Image and Full ImageChange ID Open the menu bar and click File New Album Create NEW FolderSaving Saved, you will be asked whether to save or not Open Index Save the Full Image Data Make sure all units are properly connected p Using Jlip Player Software DataEN Jlip Player Soft Ware Open Jlip jlp File window is displayed HOW to Store Jlip Player Data Save As Jlip jlp File window is displayed Problem Cause Cannot capture video data Counter cannot be resetWhere the program run file With the desired counter Message Appears when Action Playing back ErrorExecute after Not enough disk EN Memo Jlip Player Software Section EN Connections When Using Jlip Playe r Soft ware JVC Video unit Gettin G Started Installing Jlip Player Software EN To start the setup program Select Serial Port Starting Jlip Player SoftwarePrepare Devices Select Devices Display Title barIcon button File name Memo Elapsed Time Setting in/out points Operating camcorder Click Start Select SceneStart Playback Only the camcorder moves Prepare NEW Tape Basic OP Eration SDubbing Start Editing Save File Start SavingEnter File Name Select Floppy Disk Drive Correcting and cutting the programmed counter data EN BA SIC OP E RationsOpening a saved file Store Designated Scene in Memory Overwriting the fileDesignateied Scene to be COP Designate Scene to be Transferred Store button Position button Power buttonIcon button Print button MULTI-PIX button Content buttonPosition button Strobe Speed button Playback PrintingBring UP Video Printer Window Store Scene Click Close Choose Exit from File Video Printer window closes Movie Player window closes To Print Captured Video Data with Video Printer Auto CapturePreparation Load the tape into the video unit To print only the cut-in scene on the edited tape Changing ID number Connecting other device during operationEN Advan CED Oper AT Ions When Using the Video Capture Software Access Name Change Dialog BOXAccess Device Selection Dialog BOX Enter NEW Name SET NEW Name Enter Value Access Pause Time CORREC- Tion Dialog BOXEN Advanc ED Operat Ions Determine Value Power on all devices System Communication error Error - This application willThat power is on Check devices - Confirm Ajor Speci Ficat Ions Change ID COM Port Setup MenuAutomatic Capture Auto Bitmap Delete Index Image and Full Image Desktop Window Pg , 48 GV-DS1