JVC RX-8020VBK Press and hold CATV/DBS Press CATV/DBS Control, Release CATV/DBS, Release VCR1

To change the transmittable signals for operating a CATV converter or DBS tuner

1.Press and hold CATV/DBS .

2.Press CATV/DBS CONTROL.

“CALL” appears on the remote control display window.

3 Enter a manufacturer’s code using buttons 1–9, and 0.

See the following lists to find the code.

4. Release CATV/DBS .

The following buttons can be used for operating the CATV converter and DBS tuner:

CATV/DBS	:Turn on and off the CATV converter
	or DBS tuner.
CH +/–	:Change the channels.
1 – 10, 0, 100+ (+10)	:Select the channels.
	The 10 key will function as the
	ENTER button if your equipment
	requires pressing ENTER after
	selecting a channel number.

Note:

Refer also to the manual supplied with your CATV converter or

DBS tuner.

5. Try to operate your CATV converter or DBS tuner by pressing CATV/DBS .

When your CATV converter or DBS tuner turns on or off, you have entered the correct code.

If there are more than one code listed for your brand of

CATV converter or DBS tuner, try each one until the correct one is entered.

Note:

You cannot preset the signals for both the CATV converter and DBS

tuner at the same time.

	For DBS tuner
Manufacturer		Codes
JVC		56*, 57, 67
AMSTRAD		43, 44, 45, 46, 47, 48, 49
BLAUPUNKT		30
ECHOSTAR		50, 51, 67
GOLDSTAR		31
GRUNDIG		32, 33
HIRSHMANN		48, 52, 53, 54, 55
INSTRUMENT		68
ITT/NOKIA		34
KATHREIN		52, 58, 59, 60, 61, 62, 63
NEC		35, 36
ORBITECH		48
PHILIPS		37, 38
RCA		65
SAMSUNG		39, 40
SCHWAIGER		61, 64
SIEMENS		41, 42
SONY		66
TECHNISAT		48

*Initial setting

For CATV converter

Manufacturer	Codes
GENERAL INSTRUMENT	06, 07, 08, 09, 10, 11,
	12, 13, 14, 29
HAMLIN/REGAL	01, 02, 03, 04, 05
JERROLD	06, 07, 08, 09, 10, 11,
	12, 13, 14
OAK	15, 16, 17
PANASONIC	18, 19, 20
PIONEER	21, 22
SCIENTIFIC ATLANTA	23, 24, 25
TOCOM	26
ZENITH	27, 28

Manufacturers’ codes are subject to change without notice. If they are changed, this remote control cannot operate the equipment.

To change the transmittable signals for operating another manufacturer’s VCR

1.Press and hold VCR1 .

2.Press VCR1.

“CALL” appears on the remote control display window.

3. Enter manufacturer’s code using buttons 1–9, and 0.

See the list on the next page to find the code.

4. Release VCR1 .

The following buttons can be used for operating the VCR:

VCR1 :Turn on and off the VCR.

After pressing VCR1, you can perform the following operations on the VCR:

CH +/–	:Change the TV channels on the
	VCR.
1 – 10, 0, 100+ (+10)	:Select the TV channels.
	The 10 key will function as the
	ENTER button if your VCR requires
	pressing ENTER after selecting a
	channel number.
3 PLAY	:Start playback.
REW	:Rewind a tape.
FF	:Fast wind a tape.
7 STOP	:Stop playing or recording.
8 PAUSE:	:Pause playing. To resume press
	3 PLAY.
REC PAUSE	:Enter recording pause by pressing
	this button.
	To start recording again, press this
	button then 3 PLAY.

Note:

Refer also to the manual supplied with your VCR.

5. Try to operate your VCR by pressing VCR1 .

When your VCR turns on or off, you have entered the correct code.

If there are more than one code listed for your brand of

VCR, try each one until the correct one is entered.

55