JVC RX-8020VBK manual Operating JVC’s Audio/Video Components, Operating Audio Components, Tuner

Operating JVC’s Audio/Video Components

You can operate JVC’s audio and video components with this receiver’s remote control, since control signals for JVC’s components are preset in the remote control.

Operating Audio Components

IMPORTANT:

To operate JVC’s audio components using this remote control:

•You need to connect JVC’s audio components through the COMPU LINK (SYNCHRO) jacks (see page 43) in addition to the connections using cables with RCA pin plugs (see pages 8 and 9).

•Aim the remote control directly at the remote sensor on the receiver.

•If you use the buttons on the front panel to choose a source, the remote control will not operate that source. To operate a source with the remote control, the source must be selected using source selecting buttons on the remote control.

•To operate a cassette deck or MD recorder using the COMPU LINK remote control system, set the source name correctly. (See page 17.)

•Refer also to the manuals supplied with your components.

A/V CONTROL RECEIVER

CATV/DBS		VCR1	TV	AUDIO
DVD	DVD MULTI		CD	FM/AM
TV/DBS		VIDEO	CDR	PHONO
VCR1		VCR2	TAPE/MD	USB
SURROUND		DSP	SURR/DSP ANALOG/DIGITAL
			OFF	INPUT
ANALOG		BASS	∗FRONT•L	∗FRONT•R
DIRECT		BOOST
		1	2	3
			MENU
SOUND		TEST	∗CENTER	∗SUBWFR
		4	5	6
			ENTER
DIMMER			∗SURR•L	∗SURR•R
		7/P	8	9
MUTING	∗DIGITALEQ ∗SBACK•L ∗SBACK•R
		10	0	+10
		RETURN	FMMODE	100+
CATV/DBS
CONTROL		+	+	+
TV/VIDEO CH/∗LEVEL TV VOL				VOLUME
		−	−	−
TEXT		MENU	PLAY
DISPLAY				EXIT
REC		/REW	PAUSE	FF/
PAUSE
			SET
SLEEP		DOWN – TUNING – UP
			STOP	CONTROL

RM-SRX8020JREMOTE CONTROL

Note:

When you press one of the source selecting buttons, the operation mode appears on the display window. For example, the above illustration shows the remote control now works for CD operation.

Buttons	Indications
FM/AM	TUNER
CD	CD
CDR	CDR
PHONO	PHONO
TAPE/MD	TAPE
CONTROL (repeatedly)*	VCR 1	TAPE
	CDDSC	CDR
SOUND	SOUND

*By pressing CONTORL repeatedly, you can select “VCR1,” “TAPE,” “CDR” or “CDDSC” as the source.

51

Tuner

You can always perform the following operations:

FM/AM :Alternate between FM and AM.

After pressing FM/AM, you can perform the following operations:

1 – 10, +10	:Select a preset channel number directly.
	For channel number 5, press 5.
	For channel number 15, press +10, then 5.
	For channel number 20, press +10, then 10.
TUNING UP/DOWN	:Tune into stations.
FM MODE	:Change the FM reception mode.

Sound control section (Amplifier)

You can always perform the following operations:

SURROUND	:Turn on and select Surround modes
DSP	:Turn on and select DSP modes.
SURR/DSP OFF	:Turn off Surround and DSP modes.

After pressing SOUND, you can perform the following operations:

FRONT•L then LEVEL +/– :Adjust the left front speaker output level. “FRL” appears on the display.

FRONT•R then LEVEL +/– :Adjust the right front speaker output level. “FRR” appears on the display.

CENTER then LEVEL +/– :Adjust the center speaker output level. “CTR” appears on the display.

SURR•L then LEVEL +/– :Adjust the left surround speaker output level. “SURRL” appears on the display.

SURR•R then LEVEL +/– :Adjust the right surround speaker output level. “SURRR” appears on the display.

SBACK•L then LEVEL +/– :Adjust the left surround back speaker output level. “SBKL” appears on the display.

SBACK•R then LEVEL +/–	:Adjust the right surround back speaker
	output level. “SBKR” appears on the
	display.
SUBWFR then LEVEL +/–	:Adjust the subwoofer output level.
	“S-WFR” appears on the display.
DIGITAL EQ then LEVEL+/–	:Select the audio band and adjust its
	frequency level. “EQ” appears on the
	display.
TEST	:Turn on or off the test tone output.
BASS BOOST	:Turn on or off Bass Boost function.

Note:

After adjusting sounds, press the corresponding source selecting button to operate your target source by using the 10 keys; otherwise, the 10 keys cannot be used for operating your target source.

CD player

After pressing CD, you can perform the following operations on the CD player:

3 PLAY	:Start playing.
4	:Return to the beginning of the current (or previous)
	track.
¢	:Skip to the beginning of the next track.
7 STOP	:Stop playing.
8 PAUSE	:Pause playing. To resume press 3 PLAY.
1 – 10, +10	:Select a track number directly.
	For track number 5, press 5.
	For track number 15, press +10, then 5.
	For track number 20, press +10, then 10.
	For track number 30, press +10, +10, then 10.