JVC RX-F31S When your clapping sound is detected successfully, •When “MANUAL” appears, Notes

When your clapping sound is detected successfully

•On the TV screen, “SUCCESSFUL,” “RESULT,” and the setting values appear. The setting values are shown for about 12 seconds.

Ex.:

*7

SMART SURROUND SETUP L+2 C 0 R+2

+0.3m STD+0.3m

LS+6	SUCCESSFUL	RS+6	*8
+1.2m	RESULT	+1.2m
			*9
	SB+4
	+0.6m

•On the display, “SUCCESSFUL” appears, then the setting values are shown as follows for about 12 seconds:

Ex.:

*7

*8 *9

L C R RS SB LS

*7 Standard channel (the closest speaker).

This speaker position now works as the reference position (“0m/ft”) and other speakers’ distance is shown by the difference with this reference speaker position.

*8 Difference of each speaker position in distance (in meters or feet).

*9 Each speaker’s output level (–6 to +6).

When finishing displaying the setting values

On the TV screen, “COMPLETED” appears, then “TEST TONE” and “END” appear. On the display, “TEST? END?” appears.

•To adjust the speakers’ output levels manually, press TEST TONE (see page 29).

•To erase the on-screen display, press SET or any button except

TEST TONE.

•The receiver returns to normal operation mode automatically if no operations are done for about 10 seconds.

Ex.:

SMART SURROUND SETUP L+2 C 0 R+2

+0.3m STD+0.3m

LS+6	TEST TONE RS+6
+1.2m	END	+1.2m

SB+4

+0.9m

When your clapping sound is not detected correctly

“SETTING UP” appears again after one of the following messages. In this case, repeat step 3.

SILENT: • The receiver detects sound from only the left and right front speakers.

• The receiver detects no sound from the front speakers and detects sound from at least one of the other speakers.

SILENT-ALL:The receiver cannot detect any sound from any speaker for about 10 seconds.

AGAIN: • The receiver cannot detect sound from the left or right front speaker.

•The receiver fails to calculate the speakers' output level and difference of each speaker's position in distance.

In the following cases, set the speakers manually.

•When “SILENT” appears twice in succession

The setting is partially made. (The distance of the speakers from which sound has not been detected is set to “+9.0m (+30ft).”)

The receiver exits from Smart Surround Setup.

•When “MANUAL” appears

The receiver fails to detect the sound three times. The receiver exits from Smart Surround Setup.

To cancel Smart Surround Setup, press SMART SURROUND SETUP while “SETTING UP” flashes.

•No other operations can be accepted after “SETTING UP” stops flashing. Complete the Smart Surround Setup.

To check the current setting made by Smart Surround Setup,

press SMART SURROUND SETUP while the receiver is in normal operation mode.

The setting values appear. On the display, the setting values are shown one after another.

•The current setting is not indicated but “MANUAL” appears if you change the following settings after using Smart Surround Setup:

–If you change speaker distance manually.

–If you change one of the speaker sizes either from “NO” to

“SMALL” or “LARGE,” or from “SMALL” or “LARGE” to “NO.” To check the current setting, see each setting item of the speaker distance (see page 22) and the speaker output level (see page 29).

•If you have not used Smart Surround Setup, “NO S.S.S.” appears.

NOTES

•The speaker distance and output level manually set will be applied instead of those set by using Smart Surround Setup in the following cases:

–When you change one of the speaker distance (see page 22).

–When you change one of the speaker size either from “NO” to “SMALL” or “LARGE,” or from “SMALL” or “LARGE” to “NO” (see page 21).

•When you want to adjust the speaker distance and output level manually, see pages 22 and 29.

•When the headphone is in use or “DVD MULTI” is selected as the source, the receiver returns to normal operation mode without showing “TEST TONE.”

•Do not clap your hands so hard that it may hurt your hands.

17