JVC RX-F31S Basic operations, Turn on the power, Select the source to play, English, Source lamps

English

Basic operations

The on-screen display appears on the TV screen for 5 seconds (except “turning off the sounds temporarily”) to show the indication in the following cases:

–When you select the source (see right column).

–When you adjust the volume (see page 13).

–When you turn off the sounds temporarily (see page 15).

–When you select the Surround/DSP modes (see page 39). To cancel the function, set “SUPERIMPOSE” to “SUPERIMPOSE: OFF” (see page 25).

1	2	3
	Source lamps
1
2	When operating the receiver
	using the remote control, set
3	the mode selector to
	“AUDIO/TV/VCR/DBS.”

1 Turn on the power

Press STANDBY/ON (or AUDIO on the remote control).

The standby lamp goes off and the source lamp of the current

source lights in red.

Current source name appears.

EQ C.TONE		VIRTUAL SB			AUDIO P. BASS	TA	NEWS	INFO RDS	TUNED	ST	AUTO MUTING SLEEP AUTO MODE
LPCM	L	C	R		PL						ATT
DOLBY D	S . WFR LFE			NEO : 6							HP

DTS AAC		DSP 3D	MHz
	LS SB RS
96 / 24		AUTO SR	kHz

2 Select the source to play

On the front panel:

Turn SOURCE SELECTOR until the source name you want appears on the display.

The source lamp corresponding to the selected source lights in red.

•As you turn SOURCE SELECTOR, the source changes as follows:

EQ C.TONE		VIRTUAL SB AUDIO P. BASS			TA NEWS INFO RDS TUNED ST AUTO MUTING SLEEP AUTO MODE
LPCM	L	C	R	PL	ATT
DOLBY D	S . WFR LFE			NEO : 6	HP
DTS AAC				DSP 3D	MHz
	LS	SB	RS
96 / 24				AUTO SR	kHz

DVD MULTI DVR/DVD (DGT)

VCR (DIGITAL) DBS (DIGITAL)

TV (DIGITAL) FM AM

(Back to the beginning)

DVD MULTI:	Select for the DVD player using the analog
	discrete output mode (5.1-channel
	reproduction).

DVR/DVD (DGT)*:	Select for the DVD recorder or DVD player.
VCR (DIGITAL)*:	Select for the VCR.
DBS (DIGITAL)*: Select for the DBS tuner.
TV (DIGITAL)*:	Select for the TV.
FM:	Select for an FM broadcast.
AM:	Select for an AM broadcast.

From the remote control:

Press one of the source selecting buttons.

•For the tuner, press FM/AM. Each time you press FM/AM, the band alternates between “FM” and “AM.”

* Selecting the analog or digital input mode

For a component you have connected using both the analog connection and the digital connection methods (see pages 7 to 11), you need to select the correct input mode.

•You can select the digital input only for sources which you have selected digital input terminals for. (See “Setting the digital input (DIGITAL IN) terminals—DIGITAL IN 1/2/3” on page 24.)

From the remote control ONLY:

Press ANALOG/DIGITAL INPUT to select the analog or digital input mode.

•Each time you press the button, the input mode alternates between the analog input (“ANALOG”) and the digital input (“DGTL AUTO”).

This setting is memorized for each source.

DGTL AUTO: Select for the digital input mode. The receiver automatically detects the incoming signal format, then the digital signal format indicator (LPCM, DOLBY D, DTS, or DTS 96/24) for the detected signal lights up.

ANALOG: Select for the analog input mode.

To turn off the power (into standby)

Press STANDBY/ON (or AUDIO on the remote control) again.

The standby lamp lights in red.

NOTE

A small amount of power is consumed in standby mode. To turn the power off completely, unplug the AC power cord.

Initial setting: DGTL AUTO

NOTE

When you select “DVD MULTI,” “FM,” or “AM” as the source, the analog and digital input mode is not available.

12