JVC RX-F31S Tuner operations, Tuning in to stations manually, Using preset tuning, 2Press MEMORY

Tuner operations

Tuner operations are mainly done from the remote control.

When operating the receiver using the remote control, set the mode selector to “AUDIO/TV/ VCR/DBS.”

NOTE

When you have selected “FM” or “AM” by using SOURCE SELECTOR on the front panel, the remote control may not work for tuner operations. To use the remote control for tuner operations, select “FM” or “AM” by using the source selecting button on the remote control.

Setting the AM tuner interval spacing

Some countries space AM stations 9 kHz apart, and other countries use 10 kHz spacing. 9 kHz interval spacing is the initial setting.

•Be sure the receiver is turned off, but is plugged into an AC outlet when setting the AM tuner interval.

On the front panel ONLY:

To select the 10 kHz interval:

Hold down ADJUST and press STANDBY/ON. “10k STEP” appears on the display.

To change back to the 9 kHz interval:

Hold down SETTING and press STANDBY/ON. “9k STEP” appears on the display.

NOTE

When you change the AM tuner interval spacing, stored preset stations are erased. In this case, restore stations.

Tuning in to stations manually

From the remote control ONLY:

1Press FM/AM to select the band.

The last received station of the selected band is tuned in.

•Each time you press the button, the band alternates between “FM” and “AM.”

EQ C.TONE		VIRTUAL SB AUDIO P. BASS			TA NEWS INFO RDS TUNED ST AUTO MUTING SLEEP AUTO MODE
LPCM	L	C	R	PL	ATT
DOLBY D	S . WFR LFE			NEO : 6	HP
DTS AAC				DSP 3D	MHz
	LS	SB	RS
96 / 24				AUTO SR	kHz

2Press repeatedly or hold TUNING 9 or

( TUNING until the station you want is tuned in.

•Pressing (or holding) TUNING 9 increases the frequency.

•Pressing (or holding) ( TUNING decreases the frequency.

NOTES

•When you hold and release TUNING 9 or ( TUNING, the frequency keeps changing until a station is tuned in.

•When a station of sufficient signal strength is tuned in, the TUNED indicator lights up on the display.

•When an FM stereo program is received, the ST (stereo) indicator also lights up.

Using preset tuning

Once a station is assigned a channel number, the station can be quickly tuned simply by selecting the number. You can preset up to 30 FM and 15 AM stations.

To store the preset stations

Before you start, remember...

There is a time limit in doing the following steps. If the setting is canceled before you finish, start from step 2 again.

From the remote control ONLY:

1Tune in to the station you want to preset (see “Tuning in to stations manually” above).

•If you want to store the FM reception mode for this station, select the FM reception mode you want. See “Selecting the FM reception mode” on page 33.

EQ C.TONE		VIRTUAL SB AUDIO P. BASS			TA NEWS INFO RDS TUNED ST AUTO MUTING SLEEP AUTO MODE
LPCM	L	C	R	PL	ATT
DOLBY D	S . WFR LFE			NEO : 6	HP
DTS AAC				DSP 3D	MHz
	LS	SB	RS
96 / 24				AUTO SR	kHz

2Press MEMORY.

The channel number position starts flashing on the display for about 5 seconds.

EQ C.TONE		VIRTUAL SB AUDIO P. BASS			TA NEWS INFO RDS TUNED ST AUTO MUTING SLEEP AUTO MODE
LPCM	L	C	R	PL	ATT
DOLBY D	S . WFR LFE			NEO : 6	HP
DTS AAC				DSP 3D	MHz
	LS	SB	RS
96 / 24				AUTO SR	kHz

32