2 CONTROLS AND CONNECTORS

2-3 Rear Panel

1

CAM SW

ALARM

 

 

ALARM

COM

 

 

 

 

SERIES/CLOCK

 

OUT

 

IN

 

 

REC

OUT

 

 

 

WARNING

 

 

 

 

 

 

 

 

 

 

 

COM

 

 

 

 

ALARM

 

 

 

 

TAPE

 

 

 

 

 

/REC

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

RESET

 

 

END OUT

 

 

 

OUT

 

IN

OUT

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

2 3 4

 

 

 

 

 

 

 

MIC

VIDEO

AUDIO

 

 

 

 

 

 

 

IN

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

IN

IN

CAM SW

ALARM

ALARM

COM

 

SERIES/CLOCK

 

 

 

OUT

IN

REC OUT

WARNING

 

 

 

COM

ALARM

TAPE

 

/REC

 

REMOTE

 

 

 

RESET

END OUT

OUT

IN OUT

 

 

OUT

OUT

7 6 5

Connecting the wires to the terminals 8

1. Hold the button down and insert the wire over the top of the

terminal.

button 2. Release the button to lock the wire in the

terminal.

8

1Power cable

Connect the power plug to an AC 220-240 V, 50/60 Hz outlet.

2[MIC IN] mic input connector

Connect a microphone with 3.6-mm dia. plug. When signals are input from both the microphone connector and the audio input connector, audio signals are mixed and recorded.

3[VIDEO IN] video input connector (BNC) Receives composite video signals from a connected camera or other video source.

4[AUDIO IN] audio input connector (RCA)

Receives audio signals from a connected audio source.

5[AUDIO OUT] audio output connector (RCA) Outputs audio signals.

6[VIDEO OUT] video output connector (BNC) Outputs composite video signals. Input camera signals (composite video signals) can still be output through this connector even when no power is supplied to the unit (Power-Off Video Throughput function).

7[REMOTE] remote connector

Connect the optional RM-G30U remote control.

8[SERIES/CLOCK OUT] series recording signal/clock reset signal output terminal

Outputs the series recording signals or clock reset signals.

Select the output signal with the <TERMINAL SEL 1> menu switch.

Series recording signal output

When the <TERMINAL SEL 1> menu switch is set to “SERIES”, the series recording signal is output.

Connect to the other VCR series recording signal input terminal. When the tape being recorded in this unit ends, a signal is output from this terminal to the connected VCR.

Set the signal output timing with the menu switch <REC REMAIN> in the 3H to L24H Record modes or with the menu switch <COUNT END> in the 48H to 240H modes.

For details on settings, refer to the menu switch descriptions on page 21.

Clock reset signal output

When the <TERMINAL SEL 1> menu switch is set to “C.ADJ”, the clock reset signal is output when the internal clock is at AM0:00 and PM0:00. When connected to the [CLOCK IN] terminal of another SR-9240E/EK, this unit’s time can be synchronised with the time on the other VCR if the time difference is within ±30 seconds.

11

Page 10
Image 10
JVC SR-9240EK appendix Rear Panel