JVC VN-C215VP4U 39

Operation

Operation of Built-in Viewer

Using the built-in viewer enables display of a series of images, one-shot recording of images and receiving of alarm information.

Setting Up the Internet Explorer (A Pg. 40) Installing the built-in viewer

(A Pg. 42)

Screen Configuration of Built-in Viewer (A Pg. 43)

Quitting the Built-in Viewer (A Pg. 44) Shortcut for Built-in Viewer (A Pg. 44)

●For Built-in Viewer Settings please refer to the [INSTRUCTIONS] (pdf) in the supplied CD-ROM.

Contents

For Customer Use: IMPORTANT SAFEGUARDS CAUTION Information for Users on Disposal of Old Equipment [European Union] Attention: (Business users) [Other Countries outside the European Union] This START-UPGUIDE basic usage of VN- C215VP4U For detailed usage of VN-C215VP4U, please refer to AINSTRUCTIONSB For latest information, please refer to AReadmeB file in the supplied CD-ROM High anti-dustand waterproof performance High Picture Quality Wide shooting range Unblocked Design High-powervarifocal lens Setup Setting Operation Others PC Specification Requirements LAN Environment Memo： Maintenance and operating environment Handling of Equipment Others Copyrights of video Maintenance Saving Energy Camera unit A Mounting hole Note： B Holes for connection cable and piping CFall-preventionwire mounting screw I Power cable for heater (AC 24 V) (Gray, White) J Base GND cable (Purple) K Power supply/Alarm signal cable Signal name Cable color Inside the camera L[10BASE-T/100BASE-TX(PoE)] 10BASE-T/100BASE-TXterminal MRotation Knob N Rotation center mark Q [RESET] Reset button S [MONITOR] Monitor terminal (RCA pin) T Heater power connector U Heater space V Camera unit WCamera Fastening Claw 2 Monitoring Via Built-inViewer Saving JPEG images to the FTP server at regular intervals Monitoring Via Multicast Alarm Restrictions on Clients Control via customized application software Setup (A Pg. 16) step Network Settings (A Pg. 32) Internet Explorer Settings 1.Remove the dome cover 2.Remove the inner dome Setup 1.Remove the camera unit from the base 3.Mount the fall-preventionwire to a strong location 4.Mounting the base 1.Connect the LAN cable (A Pg. 26) 2.Connect the power cable, alarm cable and heater cable (A Pg. 24)(A Pg. 26)(A Pg. 27) 1.Fill up the holes with sealant 2.Mount the camera to the base 3.Secure the camera with the camera fastening screws (x2) 4.Insert the supplied silica gel 1.Remove the camera unit from the base (A Pg. 17) 2.Mount the base to the electrical box 3.The following procedures are the same as normal mounting Use the piping hole at the bottom of the base to mount the camera 2.Mount the fall-preventionwire to the base (A Pg. 18) 3.Wind the seal tape 4.Mount the base to the piping 5.Secure the base to the ceiling Using the piping hole at the side of the base to mount the camera 2.Wind the seal tape 3.Remove the piping hole plug of the base 4.Mount the piping hole plug to the piping hole at the bottom of the base 5.Mount the base to the piping Connecting to the DC12 V power supply Using the PoE What is PoE (Power over Ethernet) About the power cable Warning When connecting to a hub When connecting to a computer Cable to use Alarm Input Input requirements Alarm Output Output requirements Mounting the test monitor Adjusting the camera shooting direction Adjusting field angle, focus and brightness Field angle adjustment Focus adjustment Brightness adjustment 1.Mount the inner dome 1.Clean the dome cover 2.Mount the dome cover to the base 3.Secure the dome cover Page Estimation of total bit rate Picture Quality VGA File QVGA File Control Method Setting IP address with the default VN- C215VP4U settings (A)Assigning an IP address to VN-C215VP4U from the DHCP server (A) (B)Assigning a static IP address to VN- C215VP4U (B) IP Address setting at the computer 1.Click [Start] The computer with which 3.Select [Internet Protocol(TCP/IP)] and click [Properties] 4.Set the IP address Changing the IP address using the Internet Explorer 1.Launch the Internet Explorer on the computer Example: http://192.168.0.2 Changing the IP address using the Internet Explorer (continued) 4.Launch the Internet Explorer 5.Enter the user name and password (login as an administrator) 6.The top page of VN-C215VP4U appears 7.The Basic page with the IP address settings appears When the IP address of VN-C215VP4U is known When the IP address of VN-C215VP4U is unknown Page Setting Up the Internet Explorer Setting Up the Internet Explorer (continued) http://192.168.0.2 When Installing the built-inviewer 1.Enter the URL of the built-inviewer in the address field of Internet Explorer http://192.168.0.2/cgi-bin/c215viewing.cgi 2.Enter the user name and password 3.The viewer is installed and launched Screen Configuration of Built-inViewer A Alarm B Display Size C Pause D Capture Quitting the Built-inViewer Shortcut for Built-inViewer 1.Launch the Internet Explorer 2.Right-clickon Internet Explorer on the screen and select [Create Shortcut] 3.Right-clickon the shortcut icon on the Desktop screen and select Properties Camera Unit [Monitor Output] LAN Specifications Lens General Attachments/Accessories Dimension [Unit: mm (inch)] DOME IP FIXED C215VP4U-VN CAMERA