Kenwood TM-V708A instruction manual Power-Onmessage, Display Demonstration

POWER-ON MESSAGE

Each time you switch the transceiver ON, “HELLO !!” appears for approximately 2 seconds. You can program your favorite message in place of the factory default.

1Press [MNU] to enter Menu mode.

2Select Menu 1–1–1 (POWER-ON MSG), then press [OK].

•The display for entering a message appears and the first digit blinks.

3Turn the Tuning control to select a character.

•You can enter alphanumeric characters and special ASCII characters.

144 Press [a].

•The cursor moves to the next digit.

5Repeat steps 3 and 4 to enter up to 8 digits.

S￿w￿i￿t￿c￿h￿e￿s￿a￿m￿o￿n￿g￿t￿h￿e￿s￿e￿t￿s￿o￿f￿a￿l￿p￿h￿an￿￿u￿m￿e￿r￿i￿c￿ c￿h￿a￿r￿a￿c￿t￿e￿r￿s￿a￿n￿d￿s￿p￿e￿c￿i￿a￿l￿A￿S￿CI￿￿c￿h￿a￿r￿a￿c￿t￿e￿r￿s￿.￿

Sw￿i￿t￿c￿h￿e￿s￿￿be￿t￿w￿e￿e￿n￿￿	Ca￿n￿c￿e￿l￿s￿￿Me￿m￿￿or￿y￿￿
sm￿a￿l￿￿an￿d￿￿ca￿p￿i￿t￿a￿l￿￿	Na￿m￿e￿￿En￿t￿r￿y￿.￿￿
le￿t￿￿er￿s￿.￿￿

De￿l￿e￿t￿e￿s￿￿th￿e￿￿di￿g￿i￿t￿￿at￿￿	M￿o￿v￿e￿s￿t￿h￿e￿c￿u￿rs￿￿o￿r￿
th￿e￿￿cu￿r￿s￿o￿r￿￿po￿s￿i￿t￿i￿o￿n￿.￿￿	b￿a￿c￿k￿w￿a￿r￿d￿s￿.￿

In￿s￿e￿r￿t￿s￿￿th￿e￿￿cu￿r￿￿en￿t￿l￿y￿￿ Cl￿e￿a￿r￿s￿￿al￿￿di￿g￿i￿t￿s￿￿an￿d￿￿ se￿l￿e￿c￿t￿e￿d￿￿ch￿a￿r￿a￿c￿t￿e￿r￿.￿￿ (￿l￿e￿f￿t￿B￿A￿N￿D￿re￿t￿u￿rn￿￿￿s￿th￿e￿￿cu￿r￿s￿o￿r￿￿t￿o￿

S￿E￿L￿)￿ th￿e￿￿fi￿￿rs￿t￿￿di￿g￿i￿t￿.￿￿

6Press [OK] to complete the setting.

7Press [MNU] to exit Menu mode.

The keypad on the MC-58DM can also be used to enter alphanumeric characters in step 3. Refer to page 18.

DISPLAY DEMONSTRATION

By initiating this function, various preprogrammed displays appear. You still continue to use the transceiver normally, in this mode. Pressing a front panel key or Mic key, or turning the Tuning control restores the operating display immediately. If there is no key entry or Tuning control adjustment for approximately 10 seconds, the transceiver reverts back to Demonstration mode.

Press [F]+ POWER ON to switch this function ON (or OFF).

68