Kenwood TS-570D @1@2@3@4@5, 7!8 !9 @0, Getting Acquainted, UP/DOWN buttons, •SPLIT button

3 GETTING ACQUAINTED

@1@2@3@4@5

UP

DOWN

MR

		N.R.
		B.C.
		CW TUNE
		FILTER
		RIT/XIT
M.IN	–	+

DSP SLOPE

HIGHLOW

UT

C

W

O

L

AF	RF
4	6
2	8
0	10

PF

HF TRANSCEIVER TS-570D

ATT	PRE-AMP
VOX	PROC
SEND	AT TUNE
		CH1	CH2	CH3	MIC	LSB
PHONES		1	2	3
						USB
		ANT	REC	FINE	PWR	CW
		4	5	6
						FSK
MIC		NB	AGC/TONE REV		KEY
						FM
		7	8	9
						AM
			F.LOCK		DELAY	MENU 1MHz

CLR 0 ENT

!7Frequency control buttons

These buttons control functions related to selecting a frequency, a VFO, or a memory channel.

•UP/DOWN buttons

Press to step through all Amateur bands consecutively {page 13} or to step the transceiver frequency in 1 MHz increments {page 29}. Also used for making selections from the Menu {page￿16}, and to check Start and End frequencies for the Scan function {page 43}.

•SPLIT button

Press to use split-frequency operation which allows a different transmit frequency and receive frequency {page 23}.

•M/V button

Press to select either Memory or VFO mode {page￿40}.

•TF-SET button

While operating split-frequency, press to monitor or change your transmit frequency {page 23}.

•A=B button

Press to copy the data in the currently selected VFO over to the other VFO {page 30}.

•A/B button

Press to select either VFO A or VFO B {page 13}. Also, in menu mode, press to select either Menu A or Menu B {page 16}.

•CLEAR button

Press to reset the RIT/XIT frequency offset to zero {pages 30, 32}.

•RIT button

Press to switch ON or OFF the Receive Incremental Tuning function {page 30}.

•XIT button

Press to switch ON or OFF the Transmit Incremental Tuning function {page 32}.

SPLIT TF-SET A/B RIT

CH IF SHIFT SQL

46

M/V A=B CLEAR XIT

2 8

SCAN M>VFO M.IN

010

!7!8 !9 @0

!8SCAN button

Press to start and stop Scan functions {pages 46, 47}.

!9M>VFO button

Press to transfer data from a memory channel to a VFO {page 42}.

@0M.IN button

Writes data into a memory channel {page 39} or selects Memory Scroll mode {page 41}.

@1Quick Memory buttons

Controls the Quick Memory function {page 44}.

•M.IN button

Press to write data into Quick Memory {page 44}.

•MR button

Press to recall data from Quick Memory {page 45}.

@2FILTER button

Press to select the receive filter bandwidth in SSB, CW, FSK, or AM mode {pages 36, 38}, or press to select either narrow-band or wide-band transmit deviation in FM mode {page 22}.

Note: Selecting the narrow filter bandwidth in SSB mode requires the optional YK-88SN-1 filter {page 36}.

@3CW TUNE button

Press to activate the automatic zero-beat function for CW mode {page 21}.

@4B.C. button

Press to switch ON or OFF the DSP Beat Cancel function {page 38}.

@5 N.R. button

Press to toggle between Noise Reduction 1, Noise Reduction 2, and OFF {page 38}.

8