Kenwood TS-570D Computer Control Command Tables, Reading Command Tables, w u i o !0, e r t y

APPENDIX ●

READING COMMAND TABLES

q AC

w u i o !0

ANTENNA TUNER CONTROL

e

r

t

y

Function	Antenna Tuner THRU/IN -LINE, and tuning
	START/CANCEL
	Set	1		2		3	4	5	6	7	8	9	10	11	12	13	14
Input			A		C		P2	P3	;
	Read	1		2		3	4	5	6	7	8	9	10	11	12	13	14
			A		C	;
Output	Answer	1		2		3	4	5	6	7	8	9	10	11	12	13	14
			A		C	P1	P2	P3	;

Parameter Format Parameter function

P1	30	TUNE THRU/IN
		(Answer Only)
P2	30	TUNE THRU/IN
P3	1	TUNE OFF/ON

Note:

P1 is used for Answer only. Tuning cannot be started if P2 is in the THRU state (If P2="0", selecting "1" for P3 does not start tuning). P1: RX THRU/IN

P2: TX THRU/IN

qCommand w Name

e Function of the command

r The format of the Set command is shown. When oblique lines are drawn in the 1st and 2nd columns, there is no Set command.

tThe format of the command for reading the transceiver’s current status is shown. When oblique lines are drawn in the 1st and 2nd columns, there is no Read command.

yThe format of the command output from the transceiver is shown. When oblique lines are drawn in the 1st and 2nd columns, there is no Answer command.

u The number of command digits is shown.

i Corresponds to the parameter of the command format.

o Corresponds to the Format number in the Parameter Table. For the parameter formats, refer to the Parameter Table {page 73}.

!0Indicates the function of the parameter.

COMPUTER CONTROL COMMAND TABLES

Note: Parameters that have a Parameter Function of ÒNOT USEDÓ are not supported by this transceiver. Any character except the ASCII control codes (00 to 1Fh) and the terminator (;) may be entered for those parameters.

AC ANTENNA TUNER CONTROL

AI AUTO INFORMATION

Output Input Function

Antenna Tuner THRU/IN -LINE, and tuning

START/CANCEL

Set	1		2	3	4	5	6	7	8	9	10	11	12	13	14
		A	C		P2	P3	;
Read	1		2	3	4	5	6	7	8	9	10	11	12	13	14
		A	C	;
Answer
	1		2	3	4	5	6	7	8	9	10	11	12	13	14
		A	C	P1	P2	P3	;

Parameter Format Parameter function

P1	30	TUNE THRU/IN
		(Answer Only)
P2	30	TUNE THRU/IN
P3	1	TUNE OFF/ON

Note:

P1 is used for Answer only. Tuning cannot be started if P2 is in the THRU state (If P2="0", selecting "1" for P3 does not start tuning). P1: RX THRU/IN

P2: TX THRU/IN

Function	Auto information OFF/ON
	Set	1		2	3	4	5	6	7	8	9	10	11	12	13	14
Input			A	I	P1	;
	Read	1		2	3	4	5	6	7	8	9	10	11	12	13	14
			A	I	;
Output	Answer	1		2	3	4	5	6	7	8	9	10	11	12	13	14
			A	I	P1	;

Parameter Format Parameter function

P1 32 AI NUMBER

Note: For other commands, controls whether changing a parameter will or will not trigger the corresponding Answer command to be output.

Ex: For IF, the Answer command is output if the step frequency or RIT/XIT frequency is changed.

Switching the transceiver ON restores "0".

AG AF GAIN

AN ANTENNA NUMBER

Sets or reads AF gain.

Function

	Set	1		2	3	4	5	6	7	8	9	10	11	12	13	14
Input			A	G		P1		;
	Read	1		2	3	4	5	6	7	8	9	10	11	12	13	14
			A	G	;
Output	Answer	1		2	3	4	5	6	7	8	9	10	11	12	13	14
			A	G		P1		;

Parameter Format Parameter function

P1 31 AF GAIN

Selects antenna connector ANT 1/ ANT 2.

Function
	Set	1		2	3	4	5	6	7	8	9	10	11	12	13	14
Input			A	N	P1	;
	Read	1		2	3	4	5	6	7	8	9	10	11	12	13	14
			A	N	;
Output	Answer	1		2	3	4	5	6	7	8	9	10	11	12	13	14
			A	N	P1	;

Parameter Format Parameter function

P1	33 ANTENNA
	NUMBER

75