Kenwood TS-570D instruction manual LK Frequency Lock

APPENDIX ●

FW FILTER WIDTH

KS KEYER SPEED

Sets or reads filter bandwidth.

Function

	Set	1		2	3	4	5	6	7	8	9	10	11	12	13	14
Input			F	W			P1		;
	Read	1		2	3	4	5	6	7	8	9	10	11	12	13	14
			F	W	;
Output	Answer		F	W	3	4	P1	6	;	8	9	10	11	12	13	14
		1		2			5		7

Parameter	Format		Parameter function
P1		38	FILTER WIDTH
Note:			SSB/AM/FM
CW
0000~0079:		50 Hz	0000: Narrow
0080~0099:		80 Hz	0001~: Wide
0100~0149:		100 Hz
0150~0199:		150 Hz FSK
0200~0299:		200 Hz 0000~0499: 250 Hz
0300~0399:		300 Hz 0500~0999: 500 Hz
0400~0499:		400 Hz 1000~1499: 1000 Hz
0500~0599:		500 Hz 1500~		: 1500 Hz
0600~0999:		600 Hz
1000~1999:		1000 Hz
2000~	: 2000 Hz

Sets or reads keying speed while using the KY command.

Function

	Set	1		2	3	4	5	6	7	8	9	10	11	12	13	14
Input			K	S		P1		;
	Read	1		2	3	4	5	6	7	8	9	10	11	12	13	14
			K	S	;
Output	Answer	1		2	3	4	5	6	7	8	9	10	11	12	13	14
			K	S		P1		;

Parameter Format Parameter function

P1 42 KEYER SPEED

GT

AUTO GAIN CONTROL TIME CONSTANT

KY

CW KEYING

Sets or reads AGC time constant.

Function
	Set	1	2	3	4	5	6	7	8	9	10	11	12	13	14
Input		G	T		P1		;
	Read	1	2	3	4	5	6	7	8	9	10	11	12	13	14
		G	T	;
Output	Answer	1	2	3	4	5	6	7	8	9	10	11	12	13	14
		G	T		P1		;

Parameter Format Parameter function

P1 39 AGC TIME

CONSTANT

Note:

When in FM mode, the transceiver

returns “”.

Converts input characters into Morse code.

Function
		1	2	3	4	5	6	7	8	9	10	11	12	13	14
	Set	K	Y							P1
		15	16	17	18	19	20	21 22		23 24		25	26 27		28
Input
															;
	Read	1	2	3	4	5	6	7	8	9	10	11 12		13	14
		K	Y	;

Parameter	Format	Parameter function
P1	43	KEYER MESSAGE
P2	44	KEYER BUFFER

Note: The Set command requires a “ ” (ASCII code 20h) in the third byte position. Insert “ ” for bytes that have no characters to make a 28-byte fixed length command.

The “ ” bytes will not send any character.

Supported characters include: Letters, numbers, " ' (( )) ( ) + ,–

. / : = ?

ID IDENTIFICATION

Reads Model number of the transceiver. Parameter Format Parameter function

Function											P1	16	MODEL NUMBER
1	2	3	4	5	6	7	8	9	10	11 12	13 14

		1	2	3	4	5	6	7	8	9	10	11	12	13	14
		K	Y	P2	;
Output	Answer	15	16	17	18	19	20	21 22		23 24		25	26 27		28
		29	30 31		32	33	34	35 36		37	38 39		40 41		42

Up to 24 characters can be converted as one sentence at one time. The subsequent sentence must be keyed after the current conversion is completed.

Input Set

LK FREQUENCY LOCK

	Read		1	2	3	4	5	6	7	8	9	10	11	12	13	14
			I	D	;
Output	Answer		1	2	3	4	5	6	7	8	9	10	11	12	13	14
			I	D		P1		;
	IF	INFORMATION

Reads status of the transceiver. Parameter Format Parameter function

Function												P1	4	FREQUENCY
												P2	–	NOT USED
												P3	5	RIT/XIT FREQUENCY
1	2	3	4	5	6	7	8	9	10	11 12	13 14	P4	1	RIT OFF/ON

Sets Frequency Lock OFF/ON or reads status.

Function
	Set	1		2	3	4	5	6	7	8	9	10	11	12	13	14
Input			L	K	P1	;
	Read	1		2	3	4	5	6	7	8	9	10	11	12	13	14
			L	K	;
Output	Answer	1		2	3	4	5	6	7	8	9	10	11	12	13	14
			L	K	P1	;

Parameter Format Parameter function

P1 1 LOCK OFF/ON

Input	Set	P5	1	XIT OFF/ON
		P6	–	NOT USED

LM LOAD MESSAGE

	Read	1	2	3	4	5	6	7	8	9	10	11	12 13 14			P7	7	MEMORY CHANNEL
		I	F	;												P8	11	TX/RX
																P9	2	MODE
		1	2	3	4	5	6	7	8	9	10	11	12	13	14
																P10	3	FUNCTION
		I	F					P1								P11	1	SCAN OFF/ON
Output	Answer	15 16 17 18 19 20 21 22 23 24										25	26 27		28	P12	1	SPLIT OFF/ON
								P3			P4	P5		P7		P13	1	TONE OFF/ON
																P14	14	TONE NUMBER
		29	30 31		32 33		34 35 36			37	38	39	40 41		42
																P15	–	NOT USED
		P8	P9	P10	P11	P12	P13	P14			;

IS IF SHIFT

Function	DRU or CW message recording
	Set	1		2	3	4	5	6	7	8	9	10	11	12	13	14
Input			L	M	P1	;
	Read	1		2	3	4	5	6	7	8	9	10	11	12	13	14
			L	M	;
Output	Answer	1		2	3	4	5	6	7	8	9	10	11	12	13	14
			L	M	P1	;

Parameter Format		Parameter function
P1	45	LOAD
		MESSAGE

Sets or reads IF shift.

Function
	Set	1	2	3	4	5	6	7	8	9	10	11	12	13	14
Input		I	S	P1			P2		;
	Read	1	2	3	4	5	6	7	8	9	10	11	12	13	14
		I	S	;
Output	Answer	1	2	3	4	5	6	7	8	9	10	11	12	13	14
		I	S	P1			P2		;

Parameter Format Parameter function

P1	40	IF SHIFT
		DIRECTION
P2	41	IF SHIFT
		FREQUENCY

Note:

If P2 is positive or zero, P1 can be “+” or “”.

77