Manuals / Kodak / Household Appliance / Water Pump

Kodak 7500, 5500 manual Introduction, Installation procedure, Installation requirements

Models: 5500 7500

1 100

Download 100 pages 9.62 Kb

Page 4

1 Introduction

1 Introduction

Installation requirements

Installation procedure

The Kodak Digital Science™ Mode Setup Software 5000/7000 has been developed to enable you to customize applications using the Kodak Digital Science Document Scanner 5500 and 7500.

The Mode Setup Software offers a user-friendly interface which allows you to perform an initial installation or modification of an existing setup.

The following sections describe the installation requirements, installation procedure, logon procedure, general information regarding use of the Mode Setup Software, the Installation Instructions and the Installation Questionnaire, and the logout procedure.

The following system and cabling requirements should be verified prior to attempting to use the Mode Setup Software.

Minimum system requirements

∙IBM or IBM-compatible personal computer with access to the DOS command prompt.

∙640K RAM.

∙1.2 MB hard disk space.

∙a 720K 3 1/2" disk drive.

∙monochrome or color display.

The installation procedure is as follows:

1.Insert the Mode Setup Software diskette into the disk drive of the PC.

2.Change to the directory (i.e., “mkdir setup” or “cd setup”) where the software will be installed.

3.Copy the software from the diskette to the desired directory by typing:

Copy A:*.*

If the disk drive on your PC is not deisgnated as the A drive, substitute the correct drive in the above command string.

A-61074 April 1997

1-1

Image 4

Kodak 7500, 5500 manual Introduction, Installation procedure, Installation requirements

Contents

Installation Questionnaire Instructions Mode Setup SoftwareDocument Scanner 5500 and A-61074 Part Number 6C3944Table of contents A-61074April Installation requirements Installation procedure1 Introduction Logon procedure Using the Mode Setup Software Using the Mode Setup Software Questionnaire and Instructions Logout procedure2 Scanner configuration items Accessing the Configuration Items MenuDisplay language Measurement system Date format Sample DateMarch SlashThe default is 12 hour with AM/PM Time formatWhat Is Printed Description 2 Time Format SamplesSet time and date Valid settings FieldSoft -Loud The default is Soft The options are∙Select Disable or Enable Confirmation tonesFixed field delimiter SlashDash PeriodPrinter messages Appendix B, Language supportVersion numbers Display the curent scanner firmware versions2-12 A-61074AprilLoad scanner from laptop 5500/7500window The following window will appearLoad laptop from scanner Accessing the Mode Configuration Menu 3 Mode configuration∙Select Mode Configuration A-61074April To cancel the Mode to Mode Copy ∙Select the Copy the Mode option ∙Press EnterSelecting a mode for configuration Index format Single Level -Two Level -Two Level OffsetThree Level -Three Level Offset ModeDescription 1 Index Formats Description 1 Index Formats continued IA Field width Field A Level Field B Level Field C Level assigned Level∙ Select Field C ∙Press Enter∙ Select Fixed Field Fixed field∙Press Enter 3-12Description 2 Image Address Fields Description 3 Image Address Field Width Defaults FixedLevel rules Level to follow level option Level to follow level the Index Format optiondefined using the Index Format option Description 4 Level Rule Options and Defaults LevelLevel 0 may Display Leading Zeroes i.e IA Display formatSuppress Leading Zeroes i.e Adjoining IA Batching Length monitor ∙Select Disable or Enable On/offMinimum length Maximum length Error response Skew monitor The on/off enables or disables skew monitoring ∙Select Disable or EnableDetection range detected Footswitch Press definition ∙Select Disable or Enable Confirmation toneRelease definition Patch reader Accessory Configuration∙Select Save & Previous Menu On/off enables or disables patch reading ∙Select Disable or EnableTransfer patch definition sounds when a patch document is detected ∙Select Disable or EnableThe default for all modes is Disabled ∙Select Disable or EnableCOIN2 Port Select OCR Bar code reader Accessory ConfigurationOn/off enables or disables bar code reading ∙Select Disable or Enable3 of Interleaved 2 ofCodabar NW-7 Bar code typeCodes per document Minimum code length Maximum code height Scan direction Code quality The default for all modes is Disable ∙Select Disable or EnableBar code location To close the Printer Controller menu Printer controllerAccessory Configuration Compress Leading Zeroes i.e IA Print formatthe front printer and/or the rear printer The options areFont size ∙Comic ∙Comic ∙Cine ∙Cine Character orientationFront printer Accessory ConfigurationThe default for all modes is Disable ∙Select Disable or EnablePrint definition Per Level option3-60 Sequence Display Items box Vertical start print positionRear printer Accessory ConfigurationThe default for all modes is Disable ∙Select Disable or Enablefurther described on the following pages A-61074April Items box The default for all modes is 0.250 inches / 6 mmMode name Overrides Exiting the mode configuration menu Appendix A Default summaries Machine Configuration Defaults-AllModesDefault Value Accessory Configuration Defaults-AllModesDefault Values DescriptionMode ModeDefault Values ModeMode ModeDefault Values DescriptionMode ModeDefault Values ModeMode ModeAppendix B Language support A-61074April A-61074April A-61074April BUSINESS I M AG I N G SYSTEMS EASTMAN KODAK COMPANY Business Imaging SystemsRochester, New York A-610744/97 Eastman Kodak Company