Manuals / Kodak / Household Appliance / Water Pump

Kodak 7500, 5500 manual Bar code reader, Accessory Configuration

Models: 5500 7500

1 100

Download 100 pages 9.62 Kb

Page 64

Bar code reader

Bar code reader	NOTE: The bar code reader is an accessory which must be installed
	and enabled by your Field Engineer.

Bar code reader defines the options required when using the bar code reader accessory.

∙Select Bar Code Reader from the Mode Configuration window.

Mode Number: 01 Mode Name: MODE01 Item #: 13.0

Mode Configuration

Bar Code Reader

Single

Index Format

Patch Reader

Off

On/Off

Bar Code Type

6006

IA Field Width

COIN2 Port Select

n/a

Codes Per Document

3111

Level Rules

OCR

n/a

Minimum Code Length

Supprs

IA Display Format

Bar Code Reader

Off

Maximum Code Height

FthenR

Adjoining IA

Printr Controller

Supprs

Scan Direction

None

Batching

Front Printer

Off

Code Quality

Off

Length Monitor

Rear Printer

Off

Confirmation Tone

Off

Skew Monitor

Mode Name

MODE0

Bar Code Location

NA NA

Footswitch

Overrides

No Sav

Previous Menu

Save & End Session

Don't Save & End Session

Save & Prev Menu

Don't Save & Prev Menu

The following pages provide instructions on how to define the bar code reader options. When the patch reader definitions are complete, you will automatically be returned to this window.

To close the Bar Code Reader menu:

∙Select Previous Menu. Proceed to make any additional mode configuration definitions.

NOTE: If the bar code reader was not defined as Present during

Accessory Configuration, the following message will appear:

The accessory that you requested is not enabled in

Accessory Configuration.

∙Press Enter.

∙Exit from Mode Configuration; refer to the section entitled, Exiting Mode Configuration.

Contact your Field Engineer to install and enable this accessory.

A-61074 April 1997

3-43

Image 64

Kodak 7500, 5500 manual Bar code reader, Accessory Configuration

Contents

Installation Questionnaire Instructions Mode Setup SoftwareDocument Scanner 5500 and A-61074 Part Number 6C3944Table of contents A-61074April Installation requirements Installation procedure1 Introduction Logon procedure Using the Mode Setup Software Using the Mode Setup Software Questionnaire and Instructions Logout procedure2 Scanner configuration items Accessing the Configuration Items MenuDisplay language Measurement system Date format Sample DateMarch SlashThe default is 12 hour with AM/PM Time formatWhat Is Printed Description 2 Time Format SamplesSet time and date Valid settings FieldSoft -Loud The default is Soft The options are∙Select Disable or Enable Confirmation tonesFixed field delimiter SlashDash PeriodPrinter messages Appendix B, Language supportVersion numbers Display the curent scanner firmware versions2-12 A-61074AprilLoad scanner from laptop 5500/7500window The following window will appearLoad laptop from scanner Accessing the Mode Configuration Menu 3 Mode configuration∙Select Mode Configuration A-61074April To cancel the Mode to Mode Copy ∙Select the Copy the Mode option ∙Press EnterSelecting a mode for configuration Index format Single Level -Two Level -Two Level OffsetThree Level -Three Level Offset ModeDescription 1 Index Formats Description 1 Index Formats continued IA Field width Field A Level Field B Level Field C Level assigned Level∙ Select Field C ∙Press Enter∙ Select Fixed Field Fixed field∙Press Enter 3-12Description 2 Image Address Fields Description 3 Image Address Field Width Defaults FixedLevel rules Level to follow level option Level to follow level the Index Format optiondefined using the Index Format option Description 4 Level Rule Options and Defaults LevelLevel 0 may Display Leading Zeroes i.e IA Display formatSuppress Leading Zeroes i.e Adjoining IA Batching Length monitor ∙Select Disable or Enable On/offMinimum length Maximum length Error response Skew monitor The on/off enables or disables skew monitoring ∙Select Disable or EnableDetection range detected Footswitch Press definition ∙Select Disable or Enable Confirmation toneRelease definition Patch reader Accessory Configuration∙Select Save & Previous Menu On/off enables or disables patch reading ∙Select Disable or EnableTransfer patch definition sounds when a patch document is detected ∙Select Disable or EnableThe default for all modes is Disabled ∙Select Disable or EnableCOIN2 Port Select OCR Bar code reader Accessory ConfigurationOn/off enables or disables bar code reading ∙Select Disable or Enable3 of Interleaved 2 ofCodabar NW-7 Bar code typeCodes per document Minimum code length Maximum code height Scan direction Code quality The default for all modes is Disable ∙Select Disable or EnableBar code location To close the Printer Controller menu Printer controllerAccessory Configuration Compress Leading Zeroes i.e IA Print formatthe front printer and/or the rear printer The options areFont size ∙Comic ∙Comic ∙Cine ∙Cine Character orientationFront printer Accessory ConfigurationThe default for all modes is Disable ∙Select Disable or EnablePrint definition Per Level option3-60 Sequence Display Items box Vertical start print positionRear printer Accessory ConfigurationThe default for all modes is Disable ∙Select Disable or Enablefurther described on the following pages A-61074April Items box The default for all modes is 0.250 inches / 6 mmMode name Overrides Exiting the mode configuration menu Appendix A Default summaries Machine Configuration Defaults-AllModesDefault Value Accessory Configuration Defaults-AllModesDefault Values DescriptionMode ModeDefault Values ModeMode ModeDefault Values DescriptionMode ModeDefault Values ModeMode ModeAppendix B Language support A-61074April A-61074April A-61074April BUSINESS I M AG I N G SYSTEMS EASTMAN KODAK COMPANY Business Imaging SystemsRochester, New York A-610744/97 Eastman Kodak Company