Manuals / Kodak / Household Appliance / Water Pump

Kodak 5500, 7500 manual Codes per document

Models: 5500 7500

1 100

Download 100 pages 9.62 Kb

Page 67

Codes per document

Codes per document	Codes per document defines the number of codes per document to
	be read/decoded.
	The default for all modes is One Code Decoded.
	The options are:

—One Code Decoded—results in only the first bar code encountered on a document being read/decoded.

—All Codes Decoded—results in all bar codes encountered on a document being read/decoded.

∙Select Codes Per Document from the Bar Code Reader menu.

Mode Number: 01 Mode Name: MODE01 Item #: 13.3

Mode Configuration

Bar Code Reader

Single

Index Format

Patch Reader

Off

On/Off

Bar Code Type

6006

IA Field Width

COIN2 Port Select

n/a

Codes Per Document

3111

Level Rules

OCR

n/a

Minimum Code Length

Supprs

IA Display Format

Bar Code Reader

Off

Maximum Code Height

FthenR

Adjoining IA

Printr Controller

Supprs

Scan Direction

None

Batching

Front Printer

Off

Code Quality

Off

Length Monitor

Rear Printer

Off

Confirmation Tone

Off

Skew Monitor

Mode Name

MODE0

Bar Code Location

NA NA

Footswitch

Overrides

No Sav

Previous Menu

Save & End Session

Don't Save & End Session

Save & Prev Menu

Don't Save & Prev Menu

Codes Per Document

One Code Decoded

All Codes Decoded

Previous Menu

∙Select the desired number of codes to be read/decoded.

∙Press Enter.

NOTE: If the option All Coded Decoded is selected, you must also define the Maximum Code Height option. See the section entitled, Maximum Code Height for more information.

3-46	A-61074 April 1997

Image 67

Kodak 5500, 7500 manual Codes per document

Contents

A-61074 Part Number 6C3944 Installation Questionnaire InstructionsMode Setup Software Document Scanner 5500 andTable of contents A-61074April Installation requirements Installation procedure1 Introduction Logon procedure Using the Mode Setup Software and Instructions Logout procedure Using the Mode Setup Software QuestionnaireAccessing the Configuration Items Menu 2 Scanner configuration itemsDisplay language Measurement system Slash Date formatSample Date MarchDescription 2 Time Format Samples The default is 12 hour with AM/PMTime format What Is PrintedSet time and date Field Valid settingsThe default is Soft The options are Soft -LoudConfirmation tones ∙Select Disable or EnablePeriod Fixed field delimiterSlash DashAppendix B, Language support Printer messagesA-61074April Version numbersDisplay the curent scanner firmware versions 2-12The following window will appear Load scanner from laptop5500/7500 windowLoad laptop from scanner Accessing the Mode Configuration Menu 3 Mode configuration∙Select Mode Configuration A-61074April ∙Select the Copy the Mode option ∙Press Enter To cancel the Mode to Mode CopySelecting a mode for configuration Mode Index formatSingle Level -Two Level -Two Level Offset Three Level -Three Level OffsetDescription 1 Index Formats Description 1 Index Formats continued IA Field width Field A Level Field B Level ∙Press Enter Field C Levelassigned Level ∙ Select Field C3-12 ∙ Select Fixed FieldFixed field ∙Press EnterDescription 2 Image Address Fields Fixed Description 3 Image Address Field Width DefaultsLevel rules Level to follow level option the Index Format option Level to follow leveldefined using the Index Format option Level Description 4 Level Rule Options and DefaultsLevel 0 may Display Leading Zeroes i.e IA Display formatSuppress Leading Zeroes i.e Adjoining IA Batching Length monitor On/off ∙Select Disable or EnableMinimum length Maximum length Error response Skew monitor ∙Select Disable or Enable The on/off enables or disables skew monitoringDetection range detected Footswitch Press definition Confirmation tone ∙Select Disable or EnableRelease definition Patch reader Accessory Configuration∙Select Save & Previous Menu ∙Select Disable or Enable On/off enables or disables patch readingTransfer patch definition ∙Select Disable or Enable sounds when a patch document is detected∙Select Disable or Enable The default for all modes is DisabledCOIN2 Port Select OCR Accessory Configuration Bar code reader∙Select Disable or Enable On/off enables or disables bar code readingBar code type 3 ofInterleaved 2 of Codabar NW-7Codes per document Minimum code length Maximum code height Scan direction Code quality ∙Select Disable or Enable The default for all modes is DisableBar code location To close the Printer Controller menu Printer controllerAccessory Configuration The options are Compress Leading Zeroes i.eIA Print format the front printer and/or the rear printerFont size Character orientation ∙Comic ∙Comic ∙Cine ∙CineAccessory Configuration Front printer∙Select Disable or Enable The default for all modes is DisablePer Level option Print definition3-60 Vertical start print position Sequence Display Items boxAccessory Configuration Rear printer∙Select Disable or Enable The default for all modes is Disablefurther described on the following pages A-61074April The default for all modes is 0.250 inches / 6 mm Items boxMode name Overrides Exiting the mode configuration menu Accessory Configuration Defaults-AllModes Appendix A Default summariesMachine Configuration Defaults-AllModes Default ValueMode Default ValuesDescription ModeMode Default ValuesMode ModeMode Default ValuesDescription ModeMode Default ValuesMode ModeAppendix B Language support A-61074April A-61074April A-61074April A-610744/97 Eastman Kodak Company BUSINESS I M AG I N G SYSTEMSEASTMAN KODAK COMPANY Business Imaging Systems Rochester, New York