Manuals / Kodak / Household Appliance / Water Pump

Kodak 7500 Printer controller, To close the Printer Controller menu, Accessory Configuration

Models: 5500 7500

1 100

Download 100 pages 9.62 Kb

Page 74

Printer controller

Printer controller	NOTE: The printer controller is an accessory which must be installed
	and enabled by your Field Engineer.

Printer controller defines the options required when using the printer controller accessory with a Front Printer and/or a Rear Printer.

∙Select Printer Controller from the Mode Configuration window.

Mode Number: 01 Mode Name: MODE01 Item #: 14.0

Mode Configuration

Printer Controller

Single

Index Format

Patch Reader

Off

IA Print Format

Font Size

6006

IA Field Width

COIN2 Port Select

n/a

Character Orientation

3111

Level Rules

OCR

n/a

Supprs

IA Display Format

Bar Code Reader

Off

Previous Menu

FthenR

Adjoining IA

Printr Controller

Supprs

None

Batching

Front Printer

Off

Off

Length Monitor

Rear Printer

Off

Off

Skew Monitor

Mode Name

MODE0

NA NA

Footswitch

Overrides

No Sav

Save & End Session

Don't Save & End Session

Save & Prev Menu

Don't Save & Prev Menu

The following pages provide instructions on how to define the printer controller options. When the printer controller definitions are complete, you will automatically be returned to this window.

To close the Printer Controller menu:

∙Select Previous Menu. Proceed to make any additional mode configuration definitions.

NOTE: If the printer controller was not defined as Present during

Accessory Configuration, the following message will appear:

The accessory that you requested is not enabled in

Accessory Configuration.

∙Press Enter to clear the message.

∙Exit from Mode Configuration; refer to the section entitled, Exiting Mode Configuration.

Contact your Field Engineer to install and enable this accessory.

A-61074 April 1997

3-53

Image 74

Kodak 7500, 5500 manual Printer controller, To close the Printer Controller menu, Accessory Configuration

Contents

Document Scanner 5500 and Installation Questionnaire InstructionsMode Setup Software A-61074 Part Number 6C3944Table of contents A-61074April 1 Introduction Installation procedureInstallation requirements Logon procedure Using the Mode Setup Software Using the Mode Setup Software Questionnaire and Instructions Logout procedure2 Scanner configuration items Accessing the Configuration Items MenuDisplay language Measurement system March Date formatSample Date SlashWhat Is Printed The default is 12 hour with AM/PMTime format Description 2 Time Format SamplesSet time and date Valid settings FieldSoft -Loud The default is Soft The options are∙Select Disable or Enable Confirmation tonesDash Fixed field delimiterSlash PeriodPrinter messages Appendix B, Language support2-12 Version numbersDisplay the curent scanner firmware versions A-61074Aprilwindow Load scanner from laptop5500/7500 The following window will appearLoad laptop from scanner ∙Select Mode Configuration 3 Mode configurationAccessing the Mode Configuration Menu A-61074April To cancel the Mode to Mode Copy ∙Select the Copy the Mode option ∙Press EnterSelecting a mode for configuration Three Level -Three Level Offset Index formatSingle Level -Two Level -Two Level Offset ModeDescription 1 Index Formats Description 1 Index Formats continued IA Field width Field A Level Field B Level ∙ Select Field C Field C Levelassigned Level ∙Press Enter∙Press Enter ∙ Select Fixed FieldFixed field 3-12Description 2 Image Address Fields Description 3 Image Address Field Width Defaults FixedLevel rules Level to follow level option Level to follow level the Index Format optiondefined using the Index Format option Description 4 Level Rule Options and Defaults LevelLevel 0 may Suppress Leading Zeroes i.e IA Display formatDisplay Leading Zeroes i.e Adjoining IA Batching Length monitor ∙Select Disable or Enable On/offMinimum length Maximum length Error response Skew monitor The on/off enables or disables skew monitoring ∙Select Disable or EnableDetection range detected Footswitch Press definition ∙Select Disable or Enable Confirmation toneRelease definition ∙Select Save & Previous Menu Accessory ConfigurationPatch reader On/off enables or disables patch reading ∙Select Disable or EnableTransfer patch definition sounds when a patch document is detected ∙Select Disable or EnableThe default for all modes is Disabled ∙Select Disable or EnableCOIN2 Port Select OCR Bar code reader Accessory ConfigurationOn/off enables or disables bar code reading ∙Select Disable or EnableCodabar NW-7 3 ofInterleaved 2 of Bar code typeCodes per document Minimum code length Maximum code height Scan direction Code quality The default for all modes is Disable ∙Select Disable or EnableBar code location Accessory Configuration Printer controllerTo close the Printer Controller menu the front printer and/or the rear printer Compress Leading Zeroes i.eIA Print format The options areFont size ∙Comic ∙Comic ∙Cine ∙Cine Character orientationFront printer Accessory ConfigurationThe default for all modes is Disable ∙Select Disable or EnablePrint definition Per Level option3-60 Sequence Display Items box Vertical start print positionRear printer Accessory ConfigurationThe default for all modes is Disable ∙Select Disable or Enablefurther described on the following pages A-61074April Items box The default for all modes is 0.250 inches / 6 mmMode name Overrides Exiting the mode configuration menu Default Value Appendix A Default summariesMachine Configuration Defaults-AllModes Accessory Configuration Defaults-AllModesMode Default ValuesDescription ModeMode Default ValuesMode ModeMode Default ValuesDescription ModeMode Default ValuesMode ModeAppendix B Language support A-61074April A-61074April A-61074April Rochester, New York BUSINESS I M AG I N G SYSTEMSEASTMAN KODAK COMPANY Business Imaging Systems A-610744/97 Eastman Kodak Company