Manuals / Kodak / Household Appliance / Water Pump

Kodak 5500, 7500 manual detected

Models: 5500 7500

1 100

Download 100 pages 9.62 Kb

Page 53

Manual background

Error response	Error response defines the action taken when a document skew is
	detected.
	The default for all modes is Display and Beep.
	The options are:

—Display Error Message—results in an error message appearing on the Operator Control Panel (E107–Doc Skew Monitor Warning).

—Display and Beep—results in an error message appearing on the Operator Control Panel (E107–Doc Skew Monitor Warning), accompanied by an error tone.

—Stop, Display, & Beep—results in the transport shutting down, and an error message appearing on the Operator Control Panel (E204–Re-Scan-Skew Moniotr Er), accompanied by an error tone.

∙Select Error Response from the Skew Monitor menu.

Mode Number: 01 Mode Name: MODE01 Item #: 8.3

Mode Configuration

Skew Monitor

Single

Index Format

Patch Reader

Off

On/Off

Detection Range

6006

IA Field Width

COIN2 Port Select

n/a

Error Response

3111

Level Rules

OCR

n/a

Supprs

IA Display Format

Bar Code Reader

Off

Previous Menu

FthenR

Adjoining IA

Printr Controller

Supprs

None

Batching

Front Printer

Off

Off

Length Monitor

Rear Printer

Off

Off

Skew Monitor

Mode Name

MODE0

NA NA

Footswitch

Overrides

No Sav

Save & End Session

Don't Save & End Session

Save & Prev Menu

Don't Save & Prev Menu

Error Response

Display Error Message

Display and Beep

Stop, Display, & Beep

Previous Menu

∙Select the desired error response.

∙Press Enter.

3-32	A-61074 April 1997

Image 53

Kodak 5500, 7500 manual detected

Contents

Mode Setup Software Installation Questionnaire InstructionsDocument Scanner 5500 and A-61074 Part Number 6C3944Table of contents A-61074April 1 Introduction Installation procedureInstallation requirements Logon procedure Using the Mode Setup Software and Instructions Logout procedure Using the Mode Setup Software QuestionnaireAccessing the Configuration Items Menu 2 Scanner configuration itemsDisplay language Measurement system Sample Date Date formatMarch SlashTime format The default is 12 hour with AM/PMWhat Is Printed Description 2 Time Format SamplesSet time and date Field Valid settingsThe default is Soft The options are Soft -LoudConfirmation tones ∙Select Disable or EnableSlash Fixed field delimiterDash PeriodAppendix B, Language support Printer messagesDisplay the curent scanner firmware versions Version numbers2-12 A-61074April5500/7500 Load scanner from laptopwindow The following window will appearLoad laptop from scanner ∙Select Mode Configuration 3 Mode configurationAccessing the Mode Configuration Menu A-61074April ∙Select the Copy the Mode option ∙Press Enter To cancel the Mode to Mode CopySelecting a mode for configuration Single Level -Two Level -Two Level Offset Index formatThree Level -Three Level Offset ModeDescription 1 Index Formats Description 1 Index Formats continued IA Field width Field A Level Field B Level assigned Level Field C Level∙ Select Field C ∙Press EnterFixed field ∙ Select Fixed Field∙Press Enter 3-12Description 2 Image Address Fields Fixed Description 3 Image Address Field Width DefaultsLevel rules Level to follow level option the Index Format option Level to follow leveldefined using the Index Format option Level Description 4 Level Rule Options and DefaultsLevel 0 may Suppress Leading Zeroes i.e IA Display formatDisplay Leading Zeroes i.e Adjoining IA Batching Length monitor On/off ∙Select Disable or EnableMinimum length Maximum length Error response Skew monitor ∙Select Disable or Enable The on/off enables or disables skew monitoringDetection range detected Footswitch Press definition Confirmation tone ∙Select Disable or EnableRelease definition ∙Select Save & Previous Menu Accessory ConfigurationPatch reader ∙Select Disable or Enable On/off enables or disables patch readingTransfer patch definition ∙Select Disable or Enable sounds when a patch document is detected∙Select Disable or Enable The default for all modes is DisabledCOIN2 Port Select OCR Accessory Configuration Bar code reader∙Select Disable or Enable On/off enables or disables bar code readingInterleaved 2 of 3 ofCodabar NW-7 Bar code typeCodes per document Minimum code length Maximum code height Scan direction Code quality ∙Select Disable or Enable The default for all modes is DisableBar code location Accessory Configuration Printer controllerTo close the Printer Controller menu IA Print format Compress Leading Zeroes i.ethe front printer and/or the rear printer The options areFont size Character orientation ∙Comic ∙Comic ∙Cine ∙CineAccessory Configuration Front printer∙Select Disable or Enable The default for all modes is DisablePer Level option Print definition3-60 Vertical start print position Sequence Display Items boxAccessory Configuration Rear printer∙Select Disable or Enable The default for all modes is Disablefurther described on the following pages A-61074April The default for all modes is 0.250 inches / 6 mm Items boxMode name Overrides Exiting the mode configuration menu Machine Configuration Defaults-AllModes Appendix A Default summariesDefault Value Accessory Configuration Defaults-AllModesDescription Default ValuesMode ModeMode Default ValuesMode ModeDescription Default ValuesMode ModeMode Default ValuesMode ModeAppendix B Language support A-61074April A-61074April A-61074April EASTMAN KODAK COMPANY Business Imaging Systems BUSINESS I M AG I N G SYSTEMSRochester, New York A-610744/97 Eastman Kodak Company