Manuals / Kodak / Household Appliance / Water Pump

Kodak 7500, 5500 manual Exiting the mode configuration menu

Models: 5500 7500

1 100

Download 100 pages 9.62 Kb

Page 90

Exiting the mode configuration menu

Exiting the mode configuration menu

When all of the mode configuration options have been defined for current mode, you will exit the Mode Configuration window.

∙Select one of the options listed below from the Mode Configuration window:

Mode Number: 01 Mode Name: MODE01 Item #: 0.0

		Mode Configuration
Single	Index Format		Patch Reader		Off
6006	IA Field Width		COIN2 Port Select		n/a
3111	Level Rules		OCR		n/a
Supprs	IA Display Format		Bar Code Reader		Off
FthenR	Adjoining IA		Printr Controller		Supprs
None	Batching		Front Printer		Off
Off	Length Monitor		Rear Printer		Off
Off	Skew Monitor		Mode Name		MODE0
NA NA	Footswitch		Overrides		No Sav

Save & End Session			Don't Save & End Session
Save & Prev Menu			Don't Save & Prev Menu

—Save & End Session—results in all definitions made during the session being saved and returning to the DOS prompt.

—Save & Previous Menu—results in all definitions made during the session being saved and returning to the Configuration Selection window.

—Don't Save & End Session—results in none of the definitions made during the session being saved and returning to the DOS prompt.

—Don't Save & Previous Menu—results in none of the definitions made during the session being saved and returning to the Configuration Selection window.

—Press Enter after making your selection.

A-61074 April 1997

3-69

Image 90

Kodak 7500, 5500 manual Exiting the mode configuration menu

Contents

Document Scanner 5500 and Installation Questionnaire InstructionsMode Setup Software A-61074 Part Number 6C3944Table of contents A-61074April Installation procedure Installation requirements1 Introduction Logon procedure Using the Mode Setup Software Using the Mode Setup Software Questionnaire and Instructions Logout procedure2 Scanner configuration items Accessing the Configuration Items MenuDisplay language Measurement system March Date formatSample Date SlashWhat Is Printed The default is 12 hour with AM/PMTime format Description 2 Time Format SamplesSet time and date Valid settings FieldSoft -Loud The default is Soft The options are∙Select Disable or Enable Confirmation tonesDash Fixed field delimiterSlash PeriodPrinter messages Appendix B, Language support2-12 Version numbersDisplay the curent scanner firmware versions A-61074Aprilwindow Load scanner from laptop5500/7500 The following window will appearLoad laptop from scanner 3 Mode configuration Accessing the Mode Configuration Menu∙Select Mode Configuration A-61074April To cancel the Mode to Mode Copy ∙Select the Copy the Mode option ∙Press EnterSelecting a mode for configuration Three Level -Three Level Offset Index formatSingle Level -Two Level -Two Level Offset ModeDescription 1 Index Formats Description 1 Index Formats continued IA Field width Field A Level Field B Level ∙ Select Field C Field C Levelassigned Level ∙Press Enter∙Press Enter ∙ Select Fixed FieldFixed field 3-12Description 2 Image Address Fields Description 3 Image Address Field Width Defaults FixedLevel rules Level to follow level option Level to follow level the Index Format optiondefined using the Index Format option Description 4 Level Rule Options and Defaults LevelLevel 0 may IA Display format Display Leading Zeroes i.eSuppress Leading Zeroes i.e Adjoining IA Batching Length monitor ∙Select Disable or Enable On/offMinimum length Maximum length Error response Skew monitor The on/off enables or disables skew monitoring ∙Select Disable or EnableDetection range detected Footswitch Press definition ∙Select Disable or Enable Confirmation toneRelease definition Accessory Configuration Patch reader∙Select Save & Previous Menu On/off enables or disables patch reading ∙Select Disable or EnableTransfer patch definition sounds when a patch document is detected ∙Select Disable or EnableThe default for all modes is Disabled ∙Select Disable or EnableCOIN2 Port Select OCR Bar code reader Accessory ConfigurationOn/off enables or disables bar code reading ∙Select Disable or EnableCodabar NW-7 3 ofInterleaved 2 of Bar code typeCodes per document Minimum code length Maximum code height Scan direction Code quality The default for all modes is Disable ∙Select Disable or EnableBar code location Printer controller To close the Printer Controller menuAccessory Configuration the front printer and/or the rear printer Compress Leading Zeroes i.eIA Print format The options areFont size ∙Comic ∙Comic ∙Cine ∙Cine Character orientationFront printer Accessory ConfigurationThe default for all modes is Disable ∙Select Disable or EnablePrint definition Per Level option3-60 Sequence Display Items box Vertical start print positionRear printer Accessory ConfigurationThe default for all modes is Disable ∙Select Disable or Enablefurther described on the following pages A-61074April Items box The default for all modes is 0.250 inches / 6 mmMode name Overrides Exiting the mode configuration menu Default Value Appendix A Default summariesMachine Configuration Defaults-AllModes Accessory Configuration Defaults-AllModesMode Default ValuesDescription ModeMode Default ValuesMode ModeMode Default ValuesDescription ModeMode Default ValuesMode ModeAppendix B Language support A-61074April A-61074April A-61074April Rochester, New York BUSINESS I M AG I N G SYSTEMSEASTMAN KODAK COMPANY Business Imaging Systems A-610744/97 Eastman Kodak Company