Manuals / Kohler / Lawn and Garden / Portable Generator

Kohler 24RCL manual List of Related Literature

Models: 24RCL

1 68

Download 68 pages 26.64 Kb

Page 10

List of Related Literature

Figure 3 identifies related literature available for the generator sets covered in this manual. Only trained and qualified personnel should install or service the generator set.

Literature Type	Part Number

Specification Sheet, 24RCL	G4-228

Specification Sheet, 30RCLH	G4-230

Installation Manual, Generator Set	TP-6906

Operation Manual, KG2204 Engine	TP-6901

Service Manual, Generator Set	TP-6907

Service Manual, KG2204 Engine
Mechanical	TP-6902

Service Manual, Engine ECM
Diagnostics	TP-6903

Parts Catalog, KG2204 Engine	TP-6904

Parts Catalog, 24RCL and 30RCLH
Generator Set	TP-6908

Installation Instructions, Load Control
Module (LCM)	TT-1574

Installation Instructions, Programmable
Interface Module (PIM)	TT-1584

Operation Manual, OnCuet Plus
Software	TP-6928

Operation/Installation Manual, RXT ATS	TP-6807

Operation/Installation Manual, RDT ATS	TP-6345

Installation Manual, RSB Transfer Switch	TP-6486

Operation Manual, RSB Transfer Switch	TP-6487

Figure 3 Related Literature

10 Introduction

TP-6905 6/14

Image 10

Kohler 24RCL manual List of Related Literature

Contents

24RCL TP-69056/14Operation RDC2Product Identification Information Accessory NumberAccessory Description Controller IdentificationTable of Contents Section 5 Troubleshooting Table of Contents, continuedSection 4 Scheduled Maintenance Appendix A AbbreviationsAccidental Starting Safety Precautions and InstructionsBattery DANGERExhaust System Engine Backfire/Flash FireFuel System DANGER Hazardous NoiseHazardous Voltage/ Moving Parts DANGERHot Parts Introduction NameplateList of Related Literature Figure 3 Related LiteratureAsia Pacific Service AssistanceHeadquarters Europe, Middle East, Africa EMEA China12 Service Assistance TP-69056/14Section 1 Service Views Cooling System Detail14 Section 1 Service Views TP-69056/14Section 2 Generator Set Operation 2.2 Prestart Checklist2.1 Operating Area 2.4.1Local Starting and Stopping 2.3 Exercising the Generator Set2.4 Generator Set Operation 2.4.2Automatic Starting and StoppingAutomatic Stop System Diagnostics2.5 Exercise Automatic Start2.5.7Setting the Exerciser at Power-up 2.5.5Power Failure During Exercise2.5.6Exerciser Reset 2.5.2Unloaded Full-SpeedExercise2.5.8Changing the Exercise Setting Procedure to Change the Exercise SettingStatus Displays ATS ---- Configuration Date ---- and TimeFigure 2-2 RDC2 Main Menu Overview ---- 1.2 h Engine ---- MeteringNone/Unloaded Full Sp See Section 2.5.8, Changing the Exercise SettingFigure 2-3 Procedure to Set the Exerciser Unloaded Cycle/Loaded Full SP2.6.1Warnings 2.6 Faults2.6.3ATS Communication Errors 2.6.2ShutdownsCondition Fault RDC2Fault OnCuer CheckCoolTempHigh Frequency High Figure 2-5 Controller Fault Messages 2.6.5Event Log 2.7Model RXT Transfer Switch OperationProcedure to View Event History 2.7.1Source AvailabilityFigure 2-8 Time Delays 2.7.3Time Delays2.7.4ATS Load Control Relay Time Delay 2.7.2ATS Control Sequence of Operation3.1RDC2 Generator Set/Transfer Switch Controller 3.2 Controls and IndicatorsSection 3 RDC2 Controller Operation 3.2.2 LED Indicators 3.2.1 Controller Keypad3.2.3LCD Display 3.5 Changing Settings 3.3 Controller Power3.4 Battery Charging Procedure to Change SettingsChanging Settings on the RDC2 Controller 3.6 Controller Menus 3.7 Main Menu3.8 Overview Menu 3.9 Engine Metering MenuVoltage Calibration 3.10 Generator Metering MenuDANGER 3.11Generator Set Information Menu 3.12 Genset Run Time MenuAdjusting the Display Contrast Voltage Regulator VR Voltage AdjustSetting the Exerciser 3.13 Genset System Menu3.14 ATS Status Menu 3.15 ATS Configuration Menu Changing ATS Configuration SettingsFigure 3-16 Date and Time Menu 3.16 Date and Time Menutp6810 3.17 Networking Information Menus 3.17.1 Networking Status Submenu OnCue Plus Password 3.17.3 RBUS Information Submenu 3.17.4 Remote Devices Submenu 3.18Programmable Interface Module PIM Menus 3.19 Load Control Menus 4.1General Maintenance Section 4 Scheduled MaintenanceDANGER 50 Section 4 Scheduled Maintenance TP-69056/144.2 Service Schedule 4.3 Lubrication System 4.3.1Oil SpecificationsOil Change Procedure 4.3.2Oil CheckStop the generator set. Check the oil level. Add Reset the maintenance timer on the RDC22.Replace the oil filter Note Model 24RCL does not have an oil coolerAir Cleaner Service Procedure 4.4 Air Cleaner4.5 Exhaust System 4.6.1Checking and Filling Coolant 4.6 Cooling SystemExhaust System Inspection Points 4.6.2Cooling System Inspection 4.6.4Flushing and CleaningFlushing and Cleaning Procedure 4.6.3Draining Cooling System4.7 Ignition System Figure 4-10 Spark Plug Gap Adjustment 4.8 Battery 4.9Storage Procedure DANGER5.1 Introduction Section 5 Troubleshooting5.3 Fault Messages 5.2 USB Port5.5 Generator Set Troubleshooting Figure 5-1 General Troubleshooting Chart5.6 Controller Troubleshooting Figure 5-2 RDC2 Troubleshooting Chart64 Section 5 Troubleshooting TP-69056/14Appendix A Abbreviations for example exempli gratiakg/cm2 Page TP-69056/14 Call 1-800-544-2444or visit KOHLERPower.comPhone 920-457-4441,Fax Kohler Power Systems KOHLER CO. Kohler, Wisconsin