Manuals / Kohler / Lawn and Garden / Portable Generator

Kohler 24RCL manual ATS Configuration Menu, Changing ATS Configuration Settings

Models: 24RCL

1 68

Download 68 pages 26.64 Kb

Page 40

3.15 ATS Configuration Menu

3.15 ATS Configuration Menu

Note: The ATS Configuration menu appears only if a Model RXT transfer switch is connected.

Use the ATS Configuration submenu to check the Model RXT transfer switch system settings and time delays, and change the settings, if necessary.

Changing ATS Configuration Settings

To enable editing, press the select button. The value flashes to indicate that it can be changed. Press the up and down arrow buttons to change the value. Press the Select button to save the value shown.

Use the up and down arrow buttons to move to the next value to be changed. Repeat the adjustment process until all values are correct.

Press the down arrow until Return is displayed. Press the select button to return to the main menu.

ATS ---->	Normal Freq:
Configuration	60.0 Hz
	60.0 Hz
	Normal Voltage:
	240.0 V
	Emerg. Freq:
	60.0 Hz
	Emerg. Voltage:
	240.0 V
	Emerg. Engine
	Start: 3 sec
	Transfer From
	Normal: 3 sec
	Transfer From
	Emerg.: 120 sec
	<---- Return
	tp6810
Figure 3-15ATS Configuration Menu

40 Section 3 RDC2 Controller Operation

TP-6905 6/14

Image 40

Kohler 24RCL manual ATS Configuration Menu, Changing ATS Configuration Settings

Contents

TP-69056/14 Operation24RCL RDC2Accessory Number Accessory DescriptionProduct Identification Information Controller IdentificationTable of Contents Table of Contents, continued Section 4 Scheduled MaintenanceSection 5 Troubleshooting Appendix A AbbreviationsSafety Precautions and Instructions BatteryAccidental Starting DANGERExhaust System Engine Backfire/Flash FireFuel System Hazardous Noise Hazardous Voltage/ Moving PartsDANGER DANGERHot Parts Introduction NameplateList of Related Literature Figure 3 Related LiteratureService Assistance Headquarters Europe, Middle East, Africa EMEAAsia Pacific China12 Service Assistance TP-69056/14Section 1 Service Views Cooling System Detail14 Section 1 Service Views TP-69056/14Section 2 Generator Set Operation 2.2 Prestart Checklist2.1 Operating Area 2.3 Exercising the Generator Set 2.4 Generator Set Operation2.4.1Local Starting and Stopping 2.4.2Automatic Starting and StoppingSystem Diagnostics 2.5 ExerciseAutomatic Stop Automatic Start2.5.5Power Failure During Exercise 2.5.6Exerciser Reset2.5.7Setting the Exerciser at Power-up 2.5.2Unloaded Full-SpeedExercise2.5.8Changing the Exercise Setting Procedure to Change the Exercise SettingATS ---- Configuration Date ---- and Time Figure 2-2 RDC2 Main MenuStatus Displays Overview ---- 1.2 h Engine ---- MeteringSee Section 2.5.8, Changing the Exercise Setting Figure 2-3 Procedure to Set the ExerciserNone/Unloaded Full Sp Unloaded Cycle/Loaded Full SP2.6 Faults 2.6.3ATS Communication Errors2.6.1Warnings 2.6.2ShutdownsFault RDC2 Fault OnCuerCondition CheckCoolTempHigh Frequency High Figure 2-5 Controller Fault Messages 2.7Model RXT Transfer Switch Operation Procedure to View Event History2.6.5Event Log 2.7.1Source Availability2.7.3Time Delays 2.7.4ATS Load Control Relay Time DelayFigure 2-8 Time Delays 2.7.2ATS Control Sequence of Operation3.1RDC2 Generator Set/Transfer Switch Controller 3.2 Controls and IndicatorsSection 3 RDC2 Controller Operation 3.2.2 LED Indicators 3.2.1 Controller Keypad3.2.3LCD Display 3.3 Controller Power 3.4 Battery Charging3.5 Changing Settings Procedure to Change SettingsChanging Settings on the RDC2 Controller 3.6 Controller Menus 3.7 Main Menu3.8 Overview Menu 3.9 Engine Metering MenuVoltage Calibration 3.10 Generator Metering MenuDANGER 3.11Generator Set Information Menu 3.12 Genset Run Time MenuVoltage Regulator VR Voltage Adjust Setting the ExerciserAdjusting the Display Contrast 3.13 Genset System Menu3.14 ATS Status Menu 3.15 ATS Configuration Menu Changing ATS Configuration SettingsFigure 3-16 Date and Time Menu 3.16 Date and Time Menutp6810 3.17 Networking Information Menus 3.17.1 Networking Status Submenu OnCue Plus Password 3.17.3 RBUS Information Submenu 3.17.4 Remote Devices Submenu 3.18Programmable Interface Module PIM Menus 3.19 Load Control Menus 4.1General Maintenance Section 4 Scheduled MaintenanceDANGER 50 Section 4 Scheduled Maintenance TP-69056/144.2 Service Schedule 4.3.1Oil Specifications Oil Change Procedure4.3 Lubrication System 4.3.2Oil CheckReset the maintenance timer on the RDC2 2.Replace the oil filterStop the generator set. Check the oil level. Add Note Model 24RCL does not have an oil coolerAir Cleaner Service Procedure 4.4 Air Cleaner4.5 Exhaust System 4.6.1Checking and Filling Coolant 4.6 Cooling SystemExhaust System Inspection Points 4.6.4Flushing and Cleaning Flushing and Cleaning Procedure4.6.2Cooling System Inspection 4.6.3Draining Cooling System4.7 Ignition System Figure 4-10 Spark Plug Gap Adjustment 4.8 Battery 4.9Storage Procedure DANGERSection 5 Troubleshooting 5.3 Fault Messages5.1 Introduction 5.2 USB Port5.5 Generator Set Troubleshooting Figure 5-1 General Troubleshooting Chart5.6 Controller Troubleshooting Figure 5-2 RDC2 Troubleshooting Chart64 Section 5 Troubleshooting TP-69056/14Appendix A Abbreviations for example exempli gratiakg/cm2 Page Call 1-800-544-2444or visit KOHLERPower.com Phone 920-457-4441,Fax Kohler Power SystemsTP-69056/14 KOHLER CO. Kohler, Wisconsin