Manuals / Kohler / Lawn and Garden / Portable Generator

Kohler 24RCL manual Networking Status Submenu

Models: 24RCL

1 68

Page 43

3.17.1 Networking Status Submenu

The Networking Status submenu contains settings for OnCuer Plus. See the OnCue Plus Software Operation Manual for information about the appropriate network settings for OnCue Plus.

If DHCP is enabled, IP parameters are not displayed. If DHCP is disabled (i.e., if a static IP address is used), the IP parameters are displayed.

To enable or disable DHCP and change the IP settings, go to the Networking Configuration menu. See Section 3.17.2.

Networking---->

Information

Networking---->

Status

OnCue Status: Connected

DHCP:

Enabled

IP Address:

###.###.###.###

Subnet Mask:

###.###.###.###

Gateway:

###.###.###.###

DNS 1:

###.###.###.###

DNS 2:

###.###.###.###

Ethernet Status:

Disconnected

OnCue Server:

###.###.###.###

<---- Return

tp6804

Figure 3-18Network Status Submenu

TP-6905 6/14

Section 3 RDC2 Controller Operation 43

Page 43

Image 43

Kohler 24RCL manual Networking Status Submenu

Contents

RDC2 TP-69056/14Operation 24RCLController Identification Accessory NumberAccessory Description Product Identification InformationTable of Contents Appendix A Abbreviations Table of Contents, continuedSection 4 Scheduled Maintenance Section 5 TroubleshootingDANGER Safety Precautions and InstructionsBattery Accidental StartingExhaust System Engine Backfire/Flash FireFuel System DANGER Hazardous NoiseHazardous Voltage/ Moving Parts DANGERHot Parts Nameplate IntroductionFigure 3 Related Literature List of Related LiteratureChina Service AssistanceHeadquarters Europe, Middle East, Africa EMEA Asia PacificTP-69056/14 12 Service AssistanceCooling System Detail Section 1 Service ViewsTP-69056/14 14 Section 1 Service ViewsSection 2 Generator Set Operation 2.2 Prestart Checklist2.1 Operating Area 2.4.2Automatic Starting and Stopping 2.3 Exercising the Generator Set2.4 Generator Set Operation 2.4.1Local Starting and StoppingAutomatic Start System Diagnostics2.5 Exercise Automatic Stop2.5.2Unloaded Full-SpeedExercise 2.5.5Power Failure During Exercise2.5.6Exerciser Reset 2.5.7Setting the Exerciser at Power-upProcedure to Change the Exercise Setting 2.5.8Changing the Exercise SettingOverview ---- 1.2 h Engine ---- Metering ATS ---- Configuration Date ---- and TimeFigure 2-2 RDC2 Main Menu Status DisplaysUnloaded Cycle/Loaded Full SP See Section 2.5.8, Changing the Exercise SettingFigure 2-3 Procedure to Set the Exerciser None/Unloaded Full Sp2.6.2Shutdowns 2.6 Faults2.6.3ATS Communication Errors 2.6.1WarningsCheck Fault RDC2Fault OnCuer ConditionCoolTempHigh Frequency High Figure 2-5 Controller Fault Messages 2.7.1Source Availability 2.7Model RXT Transfer Switch OperationProcedure to View Event History 2.6.5Event Log2.7.2ATS Control Sequence of Operation 2.7.3Time Delays2.7.4ATS Load Control Relay Time Delay Figure 2-8 Time Delays3.1RDC2 Generator Set/Transfer Switch Controller 3.2 Controls and IndicatorsSection 3 RDC2 Controller Operation 3.2.1 Controller Keypad 3.2.2 LED Indicators3.2.3LCD Display Procedure to Change Settings 3.3 Controller Power3.4 Battery Charging 3.5 Changing SettingsChanging Settings on the RDC2 Controller 3.7 Main Menu 3.6 Controller Menus3.9 Engine Metering Menu 3.8 Overview MenuVoltage Calibration 3.10 Generator Metering MenuDANGER 3.12 Genset Run Time Menu 3.11Generator Set Information Menu3.13 Genset System Menu Voltage Regulator VR Voltage AdjustSetting the Exerciser Adjusting the Display Contrast3.14 ATS Status Menu Changing ATS Configuration Settings 3.15 ATS Configuration MenuFigure 3-16 Date and Time Menu 3.16 Date and Time Menutp6810 3.17 Networking Information Menus 3.17.1 Networking Status Submenu OnCue Plus Password 3.17.3 RBUS Information Submenu 3.17.4 Remote Devices Submenu 3.18Programmable Interface Module PIM Menus 3.19 Load Control Menus 4.1General Maintenance Section 4 Scheduled MaintenanceDANGER TP-69056/14 50 Section 4 Scheduled Maintenance4.2 Service Schedule 4.3.2Oil Check 4.3.1Oil SpecificationsOil Change Procedure 4.3 Lubrication SystemNote Model 24RCL does not have an oil cooler Reset the maintenance timer on the RDC22.Replace the oil filter Stop the generator set. Check the oil level. AddAir Cleaner Service Procedure 4.4 Air Cleaner4.5 Exhaust System 4.6.1Checking and Filling Coolant 4.6 Cooling SystemExhaust System Inspection Points 4.6.3Draining Cooling System 4.6.4Flushing and CleaningFlushing and Cleaning Procedure 4.6.2Cooling System Inspection4.7 Ignition System Figure 4-10 Spark Plug Gap Adjustment 4.8 Battery DANGER 4.9Storage Procedure5.2 USB Port Section 5 Troubleshooting5.3 Fault Messages 5.1 IntroductionFigure 5-1 General Troubleshooting Chart 5.5 Generator Set TroubleshootingFigure 5-2 RDC2 Troubleshooting Chart 5.6 Controller TroubleshootingTP-69056/14 64 Section 5 Troubleshootingfor example exempli gratia Appendix A Abbreviationskg/cm2 Page KOHLER CO. Kohler, Wisconsin Call 1-800-544-2444or visit KOHLERPower.comPhone 920-457-4441,Fax Kohler Power Systems TP-69056/14