Fault (RDC2) | Fault (OnCuer | Condition | Check |
| Plus) |
|
|
|
|
|
|
Over Crank | Over Crank | Three unsuccessful starting attempts. | Check the fuel supply, spark plug, |
Shutdwn |
|
| and battery. |
|
|
| Check for loose connections. |
|
|
| Contact an authorized |
|
|
| distributor/dealer for service. |
|
|
|
|
PrimLoopOpn | Primary Loop | Ignition coil 1 voltage is below normal or | Check the battery voltage. |
Warning | Open | there is an open circuit. | Contact an authorized |
|
|
| |
|
|
| distributor/dealer for service and |
|
|
| provide the fault code. |
|
|
|
|
PrimLoopSht | Primary Loop | Ignition coil 1 voltage is abnormal. | Check the battery voltage. |
Warning | Shorted |
| Contact an authorized |
|
|
| |
|
|
| distributor/dealer for service and |
|
|
| provide the fault code. |
|
|
|
|
RAM Failure | Ram Failure | An ECM memory error occurred. | Contact an authorized |
Warning |
|
| distributor/dealer for service and |
|
|
| provide the fault code. |
|
|
|
|
RunRelCoil | Run Relay Coil | Excessive current on the run (70) line. | Check for shorted relays or shorted |
Shutdwn | Overload |
| wires. |
|
|
|
|
Spd Sens Flt | Speed Sensor | Engine speed sensor has failed or engine | Contact an authorized |
Shutdwn | Fault | stalled. ECM is no longer reporting valid | distributor/dealer for service. |
|
| speed. |
|
|
|
|
|
Total Power High | Total Power | Measured load is greater than 102% of the | Reduce the load by turning off |
Shutdwn | High Shutdown | generator set power rating for more than 1 | appliances. |
|
| minute. (30RCLH only) |
|
|
|
|
|
Volts | High Generator | Generator Voltage High. Output voltage | Contact an authorized |
Shutdwn | Voltage | exceeds 120% of the system nominal voltage | distributor/dealer for service. |
|
| for more than 2 seconds. |
|
|
|
|
|
Volts | Low Generator | Generator Voltage Low. Output voltage falls | Reduce the load by turning off |
Shutdwn | Voltage | below 80% of the nominal system voltage for | appliances and restart the generator |
|
| more than 10 seconds. | set. |
|
|
| Contact an authorized |
|
|
| distributor/dealer for service. |
|
|
|
|
Volts | High Generator | Generator Voltage High. Output voltage | Contact an authorized |
Shutdwn | Voltage | exceeds 120% of the system nominal voltage | distributor/dealer for service. |
|
| for more than 2 seconds. |
|
|
|
|
|
Volts | Low Generator | Generator Voltage Low. Output voltage falls | Reduce the load by turning off |
Shutdwn | Voltage | below 80% of the nominal system voltage for | appliances and restart the generator |
|
| more than 10 seconds. | set. |
|
|
| Contact an authorized |
|
|
| distributor/dealer for service. |
|
|
|
|
Volts | High Generator | Generator Voltage High. Output voltage | Contact an authorized |
Shutdwn | Voltage | exceeds 120% of the system nominal voltage | distributor/dealer for service. |
|
| for more than 2 seconds. |
|
|
|
|
|
Volts | Low Generator | Generator Voltage Low. Output voltage falls | Reduce the load by turning off |
Shutdwn | Voltage | below 80% of the nominal system voltage for | appliances and restart the generator |
|
| more than 10 seconds. | set. |
|
|
| Contact an authorized |
|
|
| distributor/dealer for service. |
Figure 2-5 Controller Fault Messages
26 Section 2 Generator Set Operation |