Manuals / Kramer Electronics / TV and Video / Universal Remote

Kramer Electronics RC-SV manual Writing a Configuration

Models: RC-SV

1 42

Download 42 pages 42.22 Kb

Page 41

9 Writing a Configuration

Writing a Configuration

6.Select Use the following IP Address, and fill in the details as shown in Figure 54.

7.Click OK.

Figure 54: Internet Protocol (TCP/IP) Properties Window

8.2Connecting the ETHERNET Port via a Network Hub (Straight- Through Cable)

You can connect the Ethernet port of the RC device to the Ethernet port on a network hub or network router, via a straight-through cable with RJ-45 connectors.

9 Writing a Configuration

Once your configuration is ready, you can write it to the device, via the ª Write Configurationº button.

Note that if the room controller is defined as a:

Master (stand alone), the configuration is written directly to the device

Slave device (the room controller is connected to the SV-551), the configuration is written to the SV-551

In case you have written the configuration to a stand alone device and it is now connected as a slave to the SV-551, you have to write the configuration once again after defining the device as a slave.

37

Image 41

Kramer Electronics RC-SV manual Writing a Configuration

Contents

Revision RC-SV Configuration GuideThe RC Configuration Software ContentsThe Kramer RC Configuration Menus Connecting a Room Controller as a Stand Alone Device MasterKRAMER SIMPLE CREATIVE TECHNOLOGY FiguresTables 2 Overview 1 Introduction2.1 System Requirements for the Kramer RC Configuration 2 Software 3 Initial Planning 4.1 Installing the Software 4 The RC Configuration SoftwareThe Kramer RC Configuration 2 software lets you 4. Click OK The following window appears see Figure 3. Install the Kramer RC Configuration 2 application4.2 Downloading and Installing the Drivers To access the Driver Manager window 1. Open the Kramer RC Configuration 2 programFigure 6 Importing a Kramer Driver File Figure 8 and Table 1 define the Driver Manager windowFigure 7 Exporting a Kramer Driver File KRAMER SIMPLE CREATIVE TECHNOLOGYFigure 8 The Driver Manager Window The RC Configuration SoftwareFunction Table 1 Driver Manager Window FeaturesFeature Serial commands see section 4 IR commands see section 4 To write a new IR command to the RC device by some devices 4.3 Port MappingFigure 16 The Port Manager Window Figure 15 The Sony DVD Player in the RC Command AreaTable 2 The Port Manager Window Features 4.4 The Kramer RC Configuration Main WindowFigure 17 The Kramer RC Configuration Main Window The ItemFeature Table 3 Kramer RC Configuration Window FeaturesFunction Device AreaFigure 18 shows the Event Macros Tab FeatureFigure 18 Event Macros Tab Function4.4.1 The RC Command Area Figure 19 Using the Toggle 1-2-3-4 Behavior4.4.1.1 The IR, RS-232 and RS-485 Ports RC Command Area Figure 20 IR, RS-232 and RS-485 Port RC Command AreaFigure 22 Switcher Port RC Command Area 4.4.1.3 The Switcher Port RC Command Area4.4.1.4 The Keypad LCD Port RC Command Area Figure 23 Switcher Port RC Command Area5 Creating a Macro Figure 28 Selecting the Port Figure 27 Creating a New Command5.1 Labeling the Buttons 5.2.1 An RS-232 Command - Switch Input to Output 5.2 Creating a Driver Command1. Select the Relay Port for example, RELAY1 Figure 35 High Volume RC Command Figure 34 Switcher RC Command5.2.4 A Power Amplifier Command 5.2.6 Setting the Button State and Color 5.2.5 An LCD Keypad CommandFigure 36 Keypad LCD RC Command 1. Select the IGNORE BUTTON Port 6.1 The File Menu 6 The Kramer RC Configuration MenusFigure 39 Ignore RC Command Table 5 File Menu Features6.2 The Edit Menu 6.3 The Configuration MenuTable 6 Edit Menu Features Table 7 Configuration Menu FeaturesTable 8 Device Menu Features 6.4 The Device Menu6.4.1 The Connect Command Menu CommandTable 11 Help Menu Features 6.5 The Help MenuFeature Menu Command6.6 Load Firmware 4. Connect to the device 7 Connecting a Room Controller as a Stand Alone Device Master 7.2 The Device Properties Window in the Stand Alone Mode 7.1 The Port Manager in the Stand Alone Mode8.1 Connecting the ETHERNET Port directly to a PC Crossover Cable 8 Connecting via the ETHERNET2. Select Properties 4. Select Properties9 Writing a Configuration To write a configuration to the device, do the following