Manuals / Kramer Electronics / TV and Video / Universal Remote

Kramer Electronics RC-SV The Help Menu, The Device Properties Dialog Box, Connect Dialog Box

Models: RC-SV

1 42

Download 42 pages 42.22 Kb

Page 35

6.4.2The Device Properties Dialog Box

The Kramer RC Configuration Menus

6.4.2The Device Properties Dialog Box

To connect a device, open the Device menu and click Properties. The Device Properties window Appears (see Figure 45). Figure 52 shows the Device Properties window in the stand alone setup.

Table 10: Connect Dialog Box

Feature	Function
Name, IP, Gateway,	If required, change information.
Mask
Model, Serial number,	Displays information.
Port, Firmware, K-Net-
ID, MAC,
DHCP1 Enabled	Check box to enable operation in
	the DHCP mode.
	When in the DHCP mode, you
	can only change the name of the
	device.
	This process may take several
	minutes and will cause an
	automatic restart on the device.

Figure 45: Device Properties Window

6.5 The Help Menu

Figure 46 illustrates the Help menu and Table 11 defines it:

Table 11: Help Menu Features

Menu Command	Function
Check for updates	Search the Kramer
	Electronics Web site for
	software updates.
About Kramer RC	Shows the current software
Configuration	version.

Figure 46: The Help Menu

1 Dynamic Host Configuration Protocol: Allows the network administrator to distribute IP addresses from a central point and automatically send a new IP address when an Ethernet point is plugged into a different network location

31

Image 35

Kramer Electronics RC-SV The Help Menu, The Device Properties Dialog Box, Connect Dialog Box, Device Properties Window

Contents

Revision RC-SV Configuration GuideConnecting a Room Controller as a Stand Alone Device Master ContentsThe RC Configuration Software The Kramer RC Configuration MenusKRAMER SIMPLE CREATIVE TECHNOLOGY FiguresTables 2 Overview 1 Introduction2.1 System Requirements for the Kramer RC Configuration 2 Software 3 Initial Planning 4.1 Installing the Software 4 The RC Configuration SoftwareThe Kramer RC Configuration 2 software lets you 4. Click OK The following window appears see Figure 3. Install the Kramer RC Configuration 2 application4.2 Downloading and Installing the Drivers To access the Driver Manager window 1. Open the Kramer RC Configuration 2 programKRAMER SIMPLE CREATIVE TECHNOLOGY Figure 8 and Table 1 define the Driver Manager windowFigure 6 Importing a Kramer Driver File Figure 7 Exporting a Kramer Driver FileFigure 8 The Driver Manager Window The RC Configuration SoftwareFunction Table 1 Driver Manager Window FeaturesFeature Serial commands see section 4 IR commands see section 4 To write a new IR command to the RC device by some devices 4.3 Port MappingFigure 16 The Port Manager Window Figure 15 The Sony DVD Player in the RC Command AreaThe Item 4.4 The Kramer RC Configuration Main WindowTable 2 The Port Manager Window Features Figure 17 The Kramer RC Configuration Main WindowDevice Area Table 3 Kramer RC Configuration Window FeaturesFeature FunctionFunction FeatureFigure 18 shows the Event Macros Tab Figure 18 Event Macros TabFigure 20 IR, RS-232 and RS-485 Port RC Command Area Figure 19 Using the Toggle 1-2-3-4 Behavior4.4.1 The RC Command Area 4.4.1.1 The IR, RS-232 and RS-485 Ports RC Command AreaFigure 23 Switcher Port RC Command Area 4.4.1.3 The Switcher Port RC Command AreaFigure 22 Switcher Port RC Command Area 4.4.1.4 The Keypad LCD Port RC Command Area5 Creating a Macro Figure 28 Selecting the Port Figure 27 Creating a New Command5.1 Labeling the Buttons 5.2.1 An RS-232 Command - Switch Input to Output 5.2 Creating a Driver Command1. Select the Relay Port for example, RELAY1 Figure 35 High Volume RC Command Figure 34 Switcher RC Command5.2.4 A Power Amplifier Command 5.2.6 Setting the Button State and Color 5.2.5 An LCD Keypad CommandFigure 36 Keypad LCD RC Command 1. Select the IGNORE BUTTON Port Table 5 File Menu Features 6 The Kramer RC Configuration Menus6.1 The File Menu Figure 39 Ignore RC CommandTable 7 Configuration Menu Features 6.3 The Configuration Menu6.2 The Edit Menu Table 6 Edit Menu FeaturesMenu Command 6.4 The Device MenuTable 8 Device Menu Features 6.4.1 The Connect CommandMenu Command 6.5 The Help MenuTable 11 Help Menu Features Feature6.6 Load Firmware 4. Connect to the device 7 Connecting a Room Controller as a Stand Alone Device Master 7.2 The Device Properties Window in the Stand Alone Mode 7.1 The Port Manager in the Stand Alone Mode4. Select Properties 8 Connecting via the ETHERNET8.1 Connecting the ETHERNET Port directly to a PC Crossover Cable 2. Select Properties9 Writing a Configuration To write a configuration to the device, do the following