Lathem 7500E 6, . INSTALLING BATTERY (Optional)

41 40

6. INSTALLING BATTERY (Optional)

Connector

Remove the lid of the battery

compartment on the back of the unit

by pushing up the center of the lid,

and then release it from the two

clasps.

Position the battery as shown in the

figure on the left .

* The connector cord should be on the

right side, as shown in the figure.

Connect the connector. Tuck away the

connector cord into the open space in

the compartment.

Insert the lid into the slot as shown on

the left. Keep pressing it down until

it hooks to the clasp.

* Make sure the cord is not caught

when closing the lid.

Lid

Clasp

Battery

Follow the steps below to install a battery (optional) so that the clock would be operational

during a power failure.

Contents

Main Lathem Time Corporation www. lathem. com (800) 241-4990 (404) 691-1065 2 This User's Manual and its contents are copyrighted by LATHEM TIME CORP. with all rights reserved. WARNING TABLE OF CONTENTS 1. INTRODUCTION Features ENGLISH < Display > <Front view> <Back view> INTRODUCTION 2. QUICK SETUP Installing Ribbon Cassette 1 2 3 ENGLISH 6 5 Setting the Display Hours 1 2 Set the "Display Hours" Setting the Time Zone for Atomic Clock Function 5 6 4 5 DEFAULT SETTINGS Please go to "Installing the Unit" on page 9 when you are finished with the settings. ADVANCED SETTINGS CONTENTS Please go to "Installing the Unit" on page 9 when you are finished with the settings. INSTALLING THE UNIT Note: Mounting Unit on Wall Environmental Conditions Page 3. Advanced Settings Setting the Time 1 4 Example: 3 4 6 5 Setting the Date Setting the Mode Payroll Mode 13 14 Setting Weekly Period in Payroll Mode 2 Set the "Mode". 3 Set the "Starting day of the week". 2 Setting Monthly Period in Payroll Mode 1 Set the "Starting date". 3 Starting date Setting Bi-Weekly Period in Payroll Mode Set the "Starting date". 17 16 2 Set the "1st starting date". 4 Set the "2nd starting date". Setting Semi-Monthly Period in Payroll Mode Job Cost Mode 3 Set the card "Reset". 22 19 18 Setting the Print Format Set the "Date/D.O.W." print format. 1 3 2 4 Set the "Hour" print format. 6 5 Set the "Minute" print format for totals only. Setting the Rounding Special Note Regarding "Punch Rounding" Set the "Types of rounding". Set the "Rounding unit". 21 22 23 22 Setting the Auto Break Deduction 23 24 Setting the Au to Break Deduction Example Elapsed time ----- 8 hours Break duration ----- 60 min. Set the "Elapsed time". Set the "Break duration". 7 Setting the Max In 3 Set the "Max In Value". 1 Set the "Max In Override". Page 27 26 1 Setting the Button Function (In/Out) 2 27 28 Setting the Daylight Savings Time Example 29 28 Set the "starting date". 3 4 5 1 29 30 6 7 9 8 31 30 3 4 Deleting the Daylight Savings Time settings 1 2 31 32 Setting the Print Language 3 1 4. 33 32 OPERATIONS & FUNCTIONS RADIO SIGNAL RECEPTION 35 34 Resetting Settings 35 36 Resetting Cards In Job Cost Mode 37 36 Card reassign 1 2 Page Page 39 40 5. PRINT EXAMPLE 6 41 40 . INSTALLING BATTERY (Optional) 41 42 7. TROUBLESHOOTING Error No. Causes and Actions 43 42 Troubleshooting Questions & Answers 43 44 8. Warnings & Cautions Warning Caution 45 44 9. SPECIFICATIONS Limited One-Year Warranty 45 46