Adjusting Power Saver, Encrypting the disk | Lexmark C780 manual

Administrative support

Adjusting Power Saver

To adjust the Power Saver setting:

1Make sure the printer is on and Ready appears on the display.

2Press on the operator panel.

3Press until Settings appears, and then press .

4Press until Setup Menu appears, and then press .

5Press until Power Saver appears, and then press .

6Using the right and left arrows on the operator panel, enter the number of minutes for the printer to wait before entering Power Saver.

The settings available range from 1–240 minutes.

7Press .

Submitting Selection appears.

Note: You can also adjust the Power Saver setting by issuing a Printer Job Language (PJL) command. For more information, see the Technical Reference available on the Lexmark Web site at www.lexmark.com/publications.

Encrypting the disk

Warning: All resources on the hard disk and RAM will be deleted.

Note: This setting is only available when a hard disk is installed.

1Turn the printer off.

2Press and hold and while turning the printer on.

3Release both buttons when Performing Self Test appears on the display.

The printer performs its power-on sequence, and then Config Menu appears on the first line of the display.

4Press until Disk Encryption appears, and then press .

5Press until Enable appears, and then press .

Contents will be lost. Continue? appears.

6Press until Yes appears, and then press . The Encrypting Disk progress bar appears.

7When disk encryption has finished, press .

8Press until Exit Config Menu appears, and then press .

To disable disk encryption:

1Turn the printer off.

2Press and hold and while turning the printer on.

3Release both buttons when Performing Self Test appears on the display.

The printer performs its power-on sequence, and then Config Menu appears on the first line of the display.

4Press until Disk Encryption appears, and then press .

Adjusting Power Saver

80

Image 80

Lexmark C780, C782 manual Adjusting Power Saver, Encrypting the disk

Contents

C780, C782 Trademarks Safety informationEdition October Contents Contents Installing and removing options Input options Output options Internal options Installing a 2000-sheet drawer Installing and removing options Continue with Installing a 500-sheet drawer Installing a 500-sheet drawer Installing a duplex unit Installing the printer Installing an output expander Installing and removing options Installing a 5-bin mailbox Installing and removing options Removing the system board access cover Installing a StapleSmart finisherInstalling memory and option cards Installing a memory card Installing an option-added firmware card Installing a hard disk Installing and removing options Installing an option card Card Function Accessing the printer system board Removing memory and option cards Removing memory cards Removing an option card Removing a hard disk Installing and removing options Reinstalling the system board access cover Removing an option-added firmware card Printing Understanding the printer operator panel Status Indicates Button Function Sending a job to printPrinting Printing from a USB flash memory device Canceling a job from a computer running Windows Canceling a print jobCanceling a job from the printer operator panel Printing a menu settings Printing a network setupCanceling a job from a Macintosh computer Canceling a job from a Macintosh computer running Mac OS Printing a font sample list Printing a directory list Loading the trays Loading 500-sheet trays Printing Loading the 2000-sheet tray Printing Loading the multipurpose feeder Printing Loading the trays Loading the multipurpose feeder Printing on specialty media transparencies, labels, otherWindows Select File Print Linking traysMac OS Linking output bins Holding a job in the printerPrinting and deleting held jobs Value Description Printing confidential jobs WindowsMacintosh Print Time Filters Enter PIN At the printerEntering a personal identification number PIN Verify Print Reserve PrintRepeat Print Copies & Pages or General pop-up menu, choose Job Routing At the printer Print All Delete All JobName1 JobName2 Storing supplies Tips for successful printingStoring paper Avoiding jams Paper characteristics WeightMedia guidelines Paper Media specifications Unacceptable paper Selecting preprinted forms and letterhead Media specifications Selecting paperStoring paper Media specifications Printing on letterhead TransparenciesEnvelopes Selecting transparencies Labels Storing media Card stock Media sizes and support Identifying media sources and specificationsDimensions Media support by type for optional features Optional Finisher Standard Offset Staple Media types and weights input options Media types and weights output options Envelopes2 Maximum 2,3 Grain longMaximum Labels- 2,4 Media capacities Paper labelsVinyl labels Envelopes Determining the status of supplies Ready. Tray 1 Low, TrayStatus / Supplies View supplies Y K Supply Menu selection item What the setting does Conserving suppliesOrdering supplies Print cartridges Maintaining the printer Toner waste container Fuser and ITUOrdering a fuser Type of fuser Printer voltage Part number Ordering staple cartridges Recycling Lexmark productsOrdering an image transfer unit and transfer roller Clearing paper jams Identifying jams Access doors and trays Clearing paper jams Understanding jam messages Paper jam messagesMessage Check Areas What to do Expander jams Area M Area B Clearing the entire paper pathArea a Area C Area D Area Tx Area T1Area E Area L Area JArea K Clearing mailbox, finisher, or output expander jams Area M Clearing fuser jams Clearing fuser jams Clearing image transfer unit jams Clearing paper jams Clearing paper jams Clearing paper jams If you still need help Adjusting operator panel brightness and contrast Disabling operator panel menus Enabling operator panel menus Restoring factory default settingsAdministrative support Adjusting Power Saver Encrypting the disk Setting security using the Embedded Web Server EWS Setting the system passwordUsing the secure Embedded Web Server Click Configuration Supporting IPSec Internet Protocol Security Using Secure modeClick TCP/IP Port Access Using 802.1x Authenticating Click 802.1x AuthenticationClick Menu Lockout Setup Locking the operator panel menus Black only mode Confidential Print SetupClick Confidential Print Setup Printing Lockout Disabling size sensing Using the Coverage EstimatorSize sensing Configuring printer alerts Using the Setup MenuUsing MarkVision Professional Using MarkVision Messenger Online customer support Calling for service Symptom Cause SolutionChecking an unresponsive printer Check the Print as image box Set Page Protect to Off from Print Recovery Solving printing problemsTroubleshooting Output expander jams Area M Solving mailbox problemsFor more informations, see Clearing mailbox, finisher, or Option Action Solving option problemsSee Solving high capacity feeder problems Solving high capacity feeder problems Problem Solution Solving paper feed problems Solving print quality problemsSee Loading the trays or Loading Paper path Top to Bottom or Left to Right Marks occur repeatedly only in one colorMultiple times on a Marks occur down the page repeatedly in all To be replaced Cartridges BCD E Solving color quality problems Frequently asked questions FAQ about color printingWhat is RGB color? How does the printer know what color to print? What is Manual Color Correction? Is it possible to increase the gloss in the printed output? Cmyk What are Detailed Color Samples and how do I access them? European Community EC directives conformity Electronic emission noticesAvis de conformité aux normes de l’industrie du Canada 102 Industry Canada compliance statement Noise emission levels Hinweis zum GS-ZeichenGerman GS mark notice Durchschnittlicher Schallpegel dBA in 1 m Umkrei Power Saver Mode Description Power consumptionProduct energy consumption Total energy usage 106 Part Name Hazardous Substances or Elements China RoHSLaser advisory label Statement of Limited Warranty Laser notice 109 Index Index PIN 112