Table of Contents Accessories Section | Lincoln Electric SVM103-C

Return to Master TOC

Return to Master TOC

Return to Master TOC

Return to Master TOC

Section C

Section C

TABLE OF CONTENTS

- ACCESSORIES SECTION -

	Page
Accessories	Section C
Lincoln Electric Accessories	C-2
Accessory Set (K875)	C-2
Power Plug Kit (K802T)	C-2
GFCI Receptacle Kit (K896-3)	C-2
Undercarriage (K882-2)	C-2
Rotor Removal Kit	C-2
Briggs and Stratton Accessories	C-2
Foam Pre-Cleaner	C-2
Oil Gard® Low Oil Shutdown Kit	C-2
Super Lo-Tone®Muffler - Square	C-2
Semiautomatic MIG Welding with a Lincoln Weld-Pak 100 or 125	C-2

POWER-ARC 4000

Image 37

Lincoln Electric SVM103-C service manual Table of Contents Accessories Section

Contents

Safety Depends on You POWER-ARC California Proposition 65 Warnings Safety Electric Shock can kill Welding Sparks can cause fire or explosion Précautions DE Sûreté Master Table of Contents for ALL Sections Table of Contents Installation Section Technical Specifications POWER-ARC Installation Location and Ventilation Safety PrecautionsStoring PRE-OPERATION Engine Service Cert. Kool Bore Spark Arrester Welding Cable Connections Electrical Output ConnectionsCable Size for 125 amp Machine Grounding Auxiliary Power ReceptaclesPlugs and HAND-HELD Equipment Circuit Breakers Premises Wiring These Devices Without POWER-ARC Table of Contents Operation Section Operation Safety InstructionsOperating Instructions General Description Design Features Advantages Operational Features and ControlsRecommended Applications Welding Capability GENERATOR/WELDER Controls Controls and Settings 20 AMP, 120 Volt Duplex Receptacle Gasoline Engine Controls Before Starting the Engine Engine OperationStarting the Engine For a HOT Engine Generator Operation To USE the Generator AS AN Auxiliary Power SupplyGeneral Information Suggested Power Applications Running Watts Start-up Watts Table B.1 Generator Power Applications Welding Operation Table B.2 Welding APPLICATIONS/ELECTRODE Selection Guide Welding Guidelines Operation What Happens in the Arc? Correct Welding Position Correct Arc Length Use the following PracticeDo the following Butt Welds Penetration Fillet Welds Vertical-Down Welding Vertical-Up Welding Hardfacing To Reduce Wear Overhead WeldingWelding Sheet Metal Cast Iron Plate Preparation Welding Cast Iron Out-of-Position Group AWS E6011 High-Speed Group AWS E6013Low Hydrogen Group Stable-Arc E7018 Table of Contents Accessories Section OPTIONS/ACCESSORIES AccessoriesLincoln Electric Accessories Table of Contents Maintenance Section Routine and Periodic Maintenance MaintenanceEngine Maintenance Engine Adjustments Figure D.2 Clean Rotating SCREEN/FINGER GUARD/DEBRIS Guard Table D.1 Engine Maintenance Schedule Do not attempt to polish slip rings while engine is running GENERATOR/WELDER Maintenance Figure D.6. Major Component Locations Table of Contents Theory of Operation Section ENGINE, EXCITATION, Rotor and Stator Theory of Operation Figure E.3 Field Excitation and Auxiliary Power Rotor Field Feedback and Auxiliary Power Weld Winding and Reactor Auxiliary Power Overcurrent Protection Table of Contents Troubleshooting & Repair Section HOW to USE Troubleshooting Guide Troubleshooting & Repair Output Problems Troubleshooting Electric Authorized Field Ser Or contact your local LincolnVice Facility Local Lincoln Electric Authorized Field Service Facility Troubleshooting Rotor Resistance Test Engine Problems Troubleshooting Engine Throttle Adjustment Rotor Voltage Test This procedure takes approximately 15 minutes to performTest Description Materials Needed Rotor Voltage Test Test Procedure Rotor Resistance Test This procedure takes approximately 25 minutes to perform Rotor Resistance Test Figure F.3 Brushes Retained with Cable TIE This procedure takes approximately 20 minutes to perform Engine Throttle Adjustment Test Frequency Counter Method Strobe-tach MethodOscilloscope Method Wing NUT High Speed Stop Screw Normal Open Circuit Weld Voltage Waveform Scope SettingsHigh Idle no Load Normal Open Circuit Voltage Waveform 115 VAC Supply Machine Loaded Typical Weld Output WaveformMachine Loaded to 125 Amps AT 23 VAC Description Brush Removal and Replacement Procedure Brush Removal and Replacement Procedure Rheostat Removal and Replacement Figure F.7 Rheostat Removal This procedure takes approximately 35 minutes to perform Capacitor AND/OR Diode Bridge Removal and Replacement Figure F.8 Location and Discharging the Field Capacitor Procedure Capacitor Removal and REPLACE- Ment Figure F.8A Field Diode Bridge Location Procedure Field Diode Bridge Removal and Replacement This procedure takes approximately 3 hours to perform STATOR/ROTOR Removal and ReplacementInstructions STATOR/ROTOR Removal and Replacement Troubleshooting & Repair Rotor Removal Procedure Figure F.12 Checking ROTOR-STATOR AIR GAP Retest After Repair Auxiliary Power Receptacle OUTPUT1Engine Output WELDER/GENERATOR OUTPUT1 Return to Section TOC Table of Contents Diagrams Section Wiring Diagram Power ARC Diagrams DIAGRAMSG-3 DIAGRAMSG-4 Dimension Print Power ARC Return to Section TOC SVM Error Reporting Form