Lincoln Electric SVM103-C instruction

Return to Section TOC

Return to Section TOC

Return to Master TOC

Return to Master TOC

F-28	TROUBLESHOOTING & REPAIR	F-28
	TROUBLESHOOTING & REPAIR

CAPACITOR AND/OR DIODE BRIDGE REMOVAL AND REPLACEMENT

(continued)

FIGURE F.8 - LOCATION AND DISCHARGING THE FIELD CAPACITOR

Attachment for

202

202A	Attachment for
(+)	201
	201A
	(-)
	Jumper

Cable Tie

Capacitor

Return to Section TOC

Return to Section TOC

Return to Master TOC

Return to Master TOC

PROCEDURE - CAPACITOR REMOVAL AND REPLACE- MENT

1.Remove the engine spark plug wire.

2.With the 5/16” nut driver, remove the sheet metal screws that hold the top cover to the control box. Remove the top cover.

3.With the 5/16” nut driver and wrench remove the screws that hold the control panel in place. Move the panel aside as far as the leads will allow.

4.Discharge the field capacitor by connecting the jumper wire clips on the black and the red wire terminals on the top of the capacitor. See Figure F.8 for location. Leave the clips on for at least 5 seconds, then remove.

5.The capacitor is mounted in a mold- ed plastic holder. To remove it, pull out on the top of the holder, then slide it upward.

6.Snap the capacitor out of the assem- bly.

7.Loosen the two screws on the top of the capacitor. Leads 202A and 202 attach to the positive (+) terminal. Leads 201 and 201A attach to the negative (-) terminal.

8.To replace the capacitor, reattach the leads to their respective termi- nals (202A and 202 to positive (+); 201 and 201A to negative (-) and tighten the screws securely. Snap the capacitor back into the molded plastic holder and slide the holder back into position in the panel. Replace the control panel and top cover of the control box and tighten down the sheet metal screws with the 5/16” nut driver.

POWER-ARC 4000

Image 76

Lincoln Electric SVM103-C service manual Procedure Capacitor Removal and REPLACE- Ment

Contents

POWER-ARC Safety Depends on You Safety California Proposition 65 Warnings Electric Shock can kill Welding Sparks can cause fire or explosion Précautions DE Sûreté Master Table of Contents for ALL Sections Table of Contents Installation Section Installation Technical Specifications POWER-ARC Location and Ventilation Safety PrecautionsStoring PRE-OPERATION Engine Service Spark Arrester Cert. Kool Bore Electrical Output Connections Welding Cable ConnectionsCable Size for 125 amp Machine Grounding Auxiliary Power ReceptaclesPlugs and HAND-HELD Equipment Premises Wiring Circuit Breakers These Devices Without POWER-ARC Table of Contents Operation Section Safety Instructions OperationOperating Instructions General Description Operational Features and Controls Design Features AdvantagesRecommended Applications Welding Capability Controls and Settings GENERATOR/WELDER Controls Gasoline Engine Controls 20 AMP, 120 Volt Duplex Receptacle Before Starting the Engine Engine OperationStarting the Engine For a HOT Engine Generator Operation To USE the Generator AS AN Auxiliary Power SupplyGeneral Information Table B.1 Generator Power Applications Suggested Power Applications Running Watts Start-up Watts Welding Operation Welding Guidelines Table B.2 Welding APPLICATIONS/ELECTRODE Selection Guide Operation What Happens in the Arc? Correct Welding Position Correct Arc Length Practice Use the followingDo the following Butt Welds Fillet Welds Penetration Vertical-Up Welding Vertical-Down Welding Hardfacing To Reduce Wear Overhead WeldingWelding Sheet Metal Welding Cast Iron Cast Iron Plate Preparation Out-of-Position Group AWS E6011 High-Speed Group AWS E6013Low Hydrogen Group Stable-Arc E7018 Table of Contents Accessories Section OPTIONS/ACCESSORIES AccessoriesLincoln Electric Accessories Table of Contents Maintenance Section Maintenance Routine and Periodic MaintenanceEngine Maintenance Engine Adjustments Figure D.2 Clean Rotating SCREEN/FINGER GUARD/DEBRIS Guard Table D.1 Engine Maintenance Schedule GENERATOR/WELDER Maintenance Do not attempt to polish slip rings while engine is running Figure D.6. Major Component Locations Table of Contents Theory of Operation Section Theory of Operation ENGINE, EXCITATION, Rotor and Stator Rotor Field Feedback and Auxiliary Power Figure E.3 Field Excitation and Auxiliary Power Auxiliary Power Overcurrent Protection Weld Winding and Reactor Table of Contents Troubleshooting & Repair Section Troubleshooting & Repair HOW to USE Troubleshooting Guide Troubleshooting Output Problems Electric Authorized Field Ser Or contact your local LincolnVice Facility Field Service Facility Local Lincoln Electric Authorized Troubleshooting Rotor Resistance Test Engine Problems Troubleshooting Engine Throttle Adjustment This procedure takes approximately 15 minutes to perform Rotor Voltage TestTest Description Materials Needed Test Procedure Rotor Voltage Test This procedure takes approximately 25 minutes to perform Rotor Resistance Test Rotor Resistance Test Figure F.3 Brushes Retained with Cable TIE Engine Throttle Adjustment Test This procedure takes approximately 20 minutes to perform Frequency Counter Method Strobe-tach MethodOscilloscope Method Wing NUT High Speed Stop Screw Normal Open Circuit Weld Voltage Waveform Scope SettingsHigh Idle no Load Normal Open Circuit Voltage Waveform 115 VAC Supply Machine Loaded Typical Weld Output WaveformMachine Loaded to 125 Amps AT 23 VAC Brush Removal and Replacement Description Brush Removal and Replacement Procedure Procedure Rheostat Removal and Replacement Figure F.7 Rheostat Removal Capacitor AND/OR Diode Bridge Removal and Replacement This procedure takes approximately 35 minutes to perform Procedure Capacitor Removal and REPLACE- Ment Figure F.8 Location and Discharging the Field Capacitor Procedure Field Diode Bridge Removal and Replacement Figure F.8A Field Diode Bridge Location This procedure takes approximately 3 hours to perform STATOR/ROTOR Removal and ReplacementInstructions STATOR/ROTOR Removal and Replacement Troubleshooting & Repair Rotor Removal Procedure Figure F.12 Checking ROTOR-STATOR AIR GAP Auxiliary Power Receptacle OUTPUT1 Retest After RepairEngine Output WELDER/GENERATOR OUTPUT1 Return to Section TOC Table of Contents Diagrams Section Diagrams Wiring Diagram Power ARC DIAGRAMSG-3 DIAGRAMSG-4 Dimension Print Power ARC Return to Section TOC SVM Error Reporting Form