Return to Section TOC
Return to Section TOC
Return to Section TOC
Return to Section TOC
Return to Master TOC
Return to Master TOC
Return to Master TOC
Return to Master TOC
TROUBLESHOOTING & REPAIR | ||||||||
|
|
|
|
|
| |||
|
|
|
|
| ||||
Observe Safety Guidelines detailed in the beginning of this manual. |
|
|
| |||||
|
|
|
|
|
| |||
PROBLEMS |
| POSSIBLE AREAS OF |
| RECOMMENDED |
| |||
(SYMPTOMS) |
| MISADJUSTMENT(S) |
| COURSE OF ACTION |
| |||
|
|
|
|
|
|
| ||
Fault Code |
|
| Description |
| Possible Adjustment |
| ||
|
|
|
|
| ||||
Thermal LED Lit | 1. | The wire drive motor has over- | 1. | Remove any bends in the gun. | ||||
Motor overloaded, long term |
| heated. | 2. | Check to see if the wire moves | ||||
|
|
| ||||||
(Err 81 on Digital Models) |
|
|
|
| smoothly through the gun and | |||
|
|
|
| cable. |
| |||
|
|
|
|
|
|
| ||
|
|
|
|
| 3. | Check the tightness of the spin- | ||
|
|
|
|
|
| dle brake. |
| |
|
|
|
|
| 4. | Wait for the motor to cool and | ||
|
|
|
|
|
| the error to reset. |
| |
|
|
|
|
| ||||
Thermal LED Lit | 1. | The wire drive motor is in a | 1. | Verify that the motor can move | ||||
Motor overloaded, short term |
| locked state causing the motor |
| freely when the pressure arm is | ||||
| to exceed it’s maximum amper- |
| released. |
| ||||
|
|
|
|
| ||||
(Err 82 on Digital Models) |
| age draw. | 2. | Verify that the drive system is | ||||
|
|
|
|
| ||||
|
|
|
|
|
| free of dirt and debris. |
| |
|
|
|
|
| 3. | Perform the MOTOR OVER- | ||
|
|
|
|
|
| LOAD TEST. |
| |
|
|
|
|
|
|
| ||
|
|
| OUTPUT PROBLEMS |
|
|
| ||
The feeder does not power up - no | 1 | The work sense lead has an | 1. | Connect the work sense lead to | ||||
display (Digital Models) - no cold |
| open | or poor connection |
| the work in a location free of dirt | |||
feed. |
|
| (across the arc model). |
| or paint. |
| ||
NOTE: Both | LED’s should flash | 2. | The power source is off. | 2. | Turn on the power source. |
| ||
briefly | when power is | 3. | The circuit breaker for the feed- | 3. | Reset the circuit breaker. |
| ||
applied. |
| |||||||
| er on the power source may |
|
|
| ||||
|
|
|
|
|
| |||
|
|
| have | tripped. (Control cable |
|
|
| |
|
|
| model). |
|
|
| ||
|
|
|
|
|
| |||
The wire feeder powers up but | 1. | The contactor coil connections | 1. | Verify the connections. |
| |||
there is no welder output when the |
| are loose. | 2. | Check for opens in the leads. | ||||
gun trigger is pulled. The shielding |
|
|
| |||||
2. | The contactor has failed. |
|
|
| ||||
gas flows and the drive rolls turn. | 3. | Perform the CONTACTOR | ||||||
|
|
| ||||||
(Across the arc models) |
|
|
|
| TEST, replace if necessary. |
| ||
|
|
|
|
|
| |||
|
|
|
|
|
|
|
| |
CAUTION
If for any reason you do not understand the test procedures or are unable to perform the tests/repairs safely, contact the Lincoln Electric Service Department for technical troubleshooting assistance before you proceed. Call
