Console Interface for Configuration for directions | Linksys SRW208

WebView Switches

Connecting the Switch

To connect network devices to the Switch, follow these instructions:

1.Make sure all the devices you will connect to the Switch are powered off.

2.For 10/100Mbps devices, connect a Category 5 Ethernet network cable to one of the numbered ports on the Switch. For a 1000Mbps device, connect a Category 5e Ethernet network cable to one of the numbered ports on the Switch.

3.Connect the other end to a PC or other network device.

4.Repeat steps 2 and 3 to connect additional devices.

5.If you are using the mini-GBIC port, then connect the mini-GBIC module to the mini-GBIC port. For detailed instructions, refer to the module’s documentation.

6.If you will use the Switch’s console interface to configure the Switch, then connect the supplied serial cable to the Switch’s Console port, and tighten the captive retaining screws. Connect the other end to your PC’s serial port. (This PC must be running the VT100 terminal emulation software, such as HyperTerminal.)

7.Connect the supplied power cord to the Switch’s power port, and plug the other end into an electrical outlet.

IMPORTANT: Make sure you use the power cord that is supplied with the Switch. Use of a different power cord could damage the Switch.

8.Power on the network devices connected to the Switch. Each active port’s corresponding Link/Act LED will light up on the Switch. If a port has an active Gigabit connection, then its corresponding Gigabit LED will also light up.

If you will use the Switch’s console interface to configure the Switch, proceed to Chapter 4: Using the

Console Interface for Configuration for directions.

If you will use the Switch’s Web-based Utility to configure the Switch, proceed to Chapter 5: Using the

Web-based Utility for Configuration.

NOTE: If you need to reset the Switch, unplug the power cord from the back of the Switch. Wait a few seconds and then reconnect it.

Chapter 3: Connecting the Switch

15

Connecting the Switch

Image 26

Linksys SRW208 manual Console Interface for Configuration for directions

Contents

Port 10/100 Ethernet Switch Copyright and Trademarks Word definition Table of Contents WebView Switches Appendix F Warranty Information 124 Appendix B Windows Help Appendix C Downloading using XmodemAppendix D Glossary Appendix E Specifications 104 WebView Switches Front Panel of the SRW208 Front Panel of the SRW208G 18 SSH Keys Fingerprints 14 Vlan Management Vlan to Ports 44 Advanced Mode New Class Map 74 Admin Memory Logs Introduction Welcome WebView Switches What’s in this User Guide? SRW208 Front Panel Getting to Know the SwitchOverview LEDs SRW208G Front Panel Ports 1000Mbps, and adjust its speed and duplex accordingly SRW208L Front Panel Front Panel of the SRW208L SRW208P, SRW208MP Front Panel Speeds of up to 1000Mbps RJ-45 port G1 through G2 Power port is located on the back panel of the Switch Back Panel Connecting the Switch Maximum Cabling Distances From Maximum Distance Desktop Placement Before You Install the SwitchPlacement Options Rack-Mount Placement Attach the Brackets to the Switch Wall-Mount Placement Wall-Mount Template Console Interface for Configuration for directions Using the Console Interface for Configuration Configuring the HyperTerminal Application Connecting to the Switch through a Telnet Session COM1 Properties Configuring the Switch through the Console Interface Switch Main Menu System Configuration Menu System Information Management Settings 14 SSH Configuration 17 SSH Crypto Key Generation Security Settings IP Configuration Http 27 Network Configuration File Management Port Status Using the Web-based Utility for Configuration Accessing the Web-based Utility System Information Setup Tab SummaryDevice Information PoE Information Setup Tab Network SettingsIP Configuration Identification Local Time Setup Tab TimeSet Time Daylight Saving Port Management Tab Port Settings Sntp Servers Port Configuration Detail screen Port Settings Port Configuration Detail WebView Switches Port Management Tab Link Aggregation Link Aggregation Detail screen Port Management Tab Lacp Port Management Lacp Single Vlan Port Management Tab PoE Power SettingsVlan Management Tab Create Vlan Vlan Range Vlan Management Tab Port Settings 12 Vlan Management Port Settings Vlan Management Tab Ports to Vlan 13 Vlan Management Ports to Vlan Vlan Management Tab Vlan to Ports Join Vlan Detail screen Vlan Management Tab Gvrp Statistics Tab Rmon Statistics 17 Statistics Rmon Statistics Statistics Tab Rmon History Log Table Rmon History 19 Rmon History Table Statistics Tab Rmon Alarm 20 Statistics Rmon Alarm Statistics Tab Rmon Events Add Event Statistics Tab Port Utilization 22 Rmon Events Events Log Statistics Tab 802.1x Statistics Statistics Tab Gvrp Statistics ACL Tab IP Based ACL 26 ACL IP Based ACL WebView Switches ACL Tab MAC Based ACL 27 ACL Mac Based ACL Security Tab ACL Binding Security Tab Radius Security Tab TACACS+ 30 Security TACACS+ Security Tab 802.1x Settings Setting Timer screen Security Tab Port Security 33 Security Port Security Security Tab Multiple Hosts Security Tab Storm Control 34 Security Multiple Hosts QoS Tab CoS Settings QoS QoS Tab Queue Settings CoS Default QoS Tab Dscp Settings QoS Tab Bandwidth Out of Profile Dscp screen QoS Tab Basic ModeQoS Tab Advanced Mode Policy Name screen 42 Advanced Mode Out of Profile Dscp New Class Map screen Spanning Tree New Aggregate Policer screen Spanning Tree Tab STP Status 46 Spanning Tree STP Status Spanning Tree Tab Global STP Global SettingBridge Settings Spanning Tree Tab STP Port Settings 48 Spanning Tree STP Port Settings Spanning Tree Tab Rstp Port Settings 49 Spanning Tree Rstp Port Settings WebView Switches Spanning Tree Tab Mstp Instance Settings Spanning Tree Tab Mstp Properties Spanning Tree Tab Mstp Interface Settings Link is working in Rstp or STP mode Multicast Tab Igmp Snooping 53 Multicast Igmp Snooping Multicast Tab Bridge Multicast 54 Multicast Bridge Multicast Multicast Tab Bridge Multicast Forward All Snmp Tab Global Parameters Snmp Tab Views Snmp Tab Group Profile 58 Snmp Group Profile Snmp Tab Group Membership 59 Snmp Group Membership Snmp Tab Communities Base Table Snmp Tab Notification Filter Advanced Table Snmp Tab Notification Recipient 62 Snmp Notification Recipient Admin Tab User Authentication 63 Admin User Authentication Admin Tab Static Address Query Admin Tab Dynamic Address Admin Tab Logging 66 Admin Logging Admin Tab Port Mirroring Admin Tab Cable Test Admin Tab Save Configuration 69 Admin Save Configuration Admin Tab Firmware Upgrade Admin Tab Reboot Admin Tab Factory Defaults Admin Tab Server Logs Admin Tab Memory Logs Admin Tab Flash Logs Gigabit Ethernet Fiber Optic Cabling Network Neighborhood/My Network Places Appendix B Windows HelpShared Resources Appendix C Downloading using Xmodem Startup Menu Procedures Figure C-2 Send File Appendix D Glossary WebView Switches WebView Switches 100 101 102 103 Appendix E Specifications SRW208 Xmodem upgrade Tftp upgradeBootP Cable Diagnostics Port Ethertype Classification and Remarking ACLs TCP/UDP port basedDiffserv Rate Limiting Ingress policer Egress rate control Standards SRW208G 1 miniGBIC/SFP port RFC 2618 Radius Client MIB RFC 1215 Traps 110 802.1x Port Access Authentication SRW208L 113 114 115 SRW208MP With 2 SFP slots Snmp version 1, 2c, 3 with support for traps RFC 2618 Radius Client MIB, RFC 1215 Traps, Private POE MIB 118 119 SRW208P 121 122 123 Appendix F Warranty Information Limited Warranty Appendix G Regulatory Information FCC Statement 126 127 128 129 130 Appendix H Contact Information