Return Boot Sector Firmware Part Number | M-S Cash Drawer A794

Chapter 6: Programming Information

A794 Owner’s Guide

Return Boot Sector Firmware Part Number

ASCII	GS NULL
Hexadecimal	1D 00
Decimal	29 0

Returns ACK (Hex 06) + 12 bytes ASCII string describing the Flash Memory Boot sector Firmware part number. Ex : 189-1234567A

Exceptions

Available only in Download Mode.

Return Segment Number Status of Flash Memory

ASCII	GS SOH
Hexadecimal	1D 01
Decimal	29 1

Returns the size of the Flash used. There may be 4, 8, or 16 sectors (64K each) in Flash Memory. This command assures that the firmware to be downloaded is the appropriate size for Flash Memory. The value returned is the maximum sector number that can be accepted by the Select Sector to Download (1D 02 nn) command.

Exceptions

Available only in Download Mode.

Select Flash Memory Sector to Download

ASCII	GS STX nn
Hexadecimal	1D 02 nn
Decimal	29 2 nn
Value of n:	the Flash sector to which the next download operation applies
Range of n:	0

Selects the Flash sector (nn) for which the next download operation applies. The values of the possible sector are restricted, depending upon the Flash part type. The printer transmits an ACK if the sector number is acceptable or an NAK if the sector number is not acceptable. Sector numbers start at 0.

Exceptions

Available only in Download Mode.

Get Firmware CRC

ASCII	GS ACK
Hexadecimal	1D 06
Decimal	29 6

Causes the printer to calculate the CRC for the currently selected sector and transmits the result. This is performed normally after downloading a sector to verify that the downloaded firmware is correct. The printer also calculates the CRC for each sector during power up and halts the program if any sector is erroneous.

The printer transmits ACK if the calculated CRC is correct for the selected sector; NAK if the CRC is incorrect or if no sector is selected.

136	December 1999

Image 141

M-S Cash Drawer A794 manual Return Boot Sector Firmware Part Number, Return Segment Number Status of Flash Memory

Contents

Owners Guide Disclaimer Legal Notices Power Supply Contents Programming Information Communication Interface Features Options Description of Printer Models AvailableModel Identification Communication Interfaces Description of Printer Models Available Model IdentificationCommunication Interfaces Options Features Unpack the Printer Choose a LocationConnect the Cables Unpack the Printer A794 Thermal Receipt Printer Setup Guide Remove the Starter Paper Roll Supports Choose a Location Setting up the printerOn a Flat Surface On a Wall Communication Cable Connect the Cables Cash Drawer Cables Power Supply Cable Printer Controls Reset ButtonPaper Feed Button LED Tone To Load the Paper Loading Receipt Paper Using the Printer Paper jams Troubleshooting the Printer To start the test Configuring the Printer Poorly printed test printout Troubleshooting the Printer Printer Tone and Green LED Troubleshooting the Printer Changing this setting Printing ProblemsPrinter Does Not Function USE Caution when This page intentionally left blank Thermal Paper Specifications Manufacturers How to Order Ordering Thermal PaperOrdering Miscellaneous Supplies How to Order Thermal Paper SpecificationsOrdering Thermal Paper Manufacturers Ordering Power Supply and Power Cord Ordering Miscellaneous SuppliesOrdering Cash Drawers Wall-Mount Kit Ordering Communication Cables Characters Paper Specifications Print ZonesPrint Modes Size Print Zones for 80 mm Paper Print Zones for 82.5 mm Paper Print Modes CharactersSize Standard Paper Specifications Print ZonesPrint Zones for 80 mm Paper Print Specifications Print Zones for 82.5 mm Paper To change the Print Density Print Density and Density of Receipt Print Lines Duty Cycle Restrictions Printing Solid Blocks Code Character Sets Code Code Code Code Code Code Code Code Communication Overview Interface Sending CommandsRS-232C Interface Parallel Interface Using DOS to Send Commands Sending CommandsUsing Basic to Send Commands Communication Overview Print Speed and Timing RS-232C Interface XON/XOFF Protocol Communication Connectors RS-232C Technical SpecificationsPin DB-9 Connector Pin DB-25 Connector DTR/DSR Protocol Cash Drawer Connector Power Connector XON/XOFF, DTR/DSR RS-232C Settings Parallel Interface Ieee Bi-directional Parallel Connector Command Conventions List of Commands and Locations Comparisons Command DescriptionsBy Command Code By Function Ascii Command Conventions By Command Code List of Commands and Location 1B 49 n Select or Cancel Italic Print 1B 2D n Select or Cancel Underline Mode1B 4C Select Page Mode 1B 54 n Select Print Direction in Page Mode 1D 42 n Select or Cancel White/Black Reverse Print Mode 1D 3A Select or Cancel Macro Definition1D 21 n Select Character Size 1D 22 55 n1 n2 Flash Memory User Sectors Allocation 04 n Convert 6 Dots/mm Bitmap to 8 Dots/mm Bitmap Print Bar Code05 n Select Superscript or Subscript Modes Print Test Form Vertical Positioning and Print Commands Printer Function CommandsBy Function Perform Partial Knife Cut Print Characteristic Commands Horizontal Positioning Commands1B 74 n Select International Character Set 1F 05 n Select Superscript or Subscript Modes Graphics Commands Status Commands1F 04 n Convert 6 Dots/mm Bitmap to 8 Dots/mm 100 Mode Commands Barcode CommandsMacro Commands User Data Storage Commands Flash Download Commands 24 n1 n2 Comparisons Printer Function Commands Command DescriptionsClear Printer Perform Full Knife Cut Generate Tone Perform Partial Knife CutSelect Peripheral Device for Multi-Drop Ascii ESC BEL Initialize Printer Hexadecimal Decimal Default Select Paper Sensors to Output Paper End Signals Default of nRange of n Select Sensors to Stop Printing Enable or Disable Panel Button Generate Pulse to Open Cash Drawer Select Cut Mode and Cut PaperValue of p1 Value of p2 AX t Print Test Form Print and Feed One Line Vertical Positioning and Print CommandsActivate Carriage Return Feed n Print Lines Range of n Default Feed n Dot RowsAdd n Extra Dot Rows Set Line Spacing to 1/6 Inch PrintSet Line Spacing Ascii ETB Print and Feed n Lines Print and Feed PaperSet Horizontal and Vertical Minimum Motion Units GS P x y Horizontal Tab Horizontal Positioning CommandsSet Column Ascii HT Compatibility Information A794 receipt vs. A793 receipt Set Absolute Starting Position Set Horizontal Tab Positions Value of k Default To move to the left Set Relative Print Position Select Justification GS L nL nH Set Left Margin Set Printing Area Width Select Double-Wide Characters Print Characteristics CommandsSelect Single-Wide Characters Ascii DC2 Select 90 Degree Counter-Clockwise Rotated Print Select Pitch Column WidthAscii ESC DC2 Set Right-Side Character Spacing Select Print Mode Define User-Defined Character Set Select or Cancel User-Defined Character SetException Values and Ranges Select or Cancel Underline Mode Copy Character Set from ROM to RAM Cancel User-Defined CharacterESC 0 0 ESC ? n Select or Cancel Double Strike Select or Cancel Emphasized Mode Select or Cancel Italic Print Select or Cancel 90 Degree Clockwise Rotated Print Select or Cancel Upside Down Print ModeSelect Character Size Normal Select or Cancel Smoothing Mode Select Or Cancel White/Black Reverse Print Mode Summary of Rotated Printing Select Superscript or Subscript Modes Print Raster Graphics Graphics Commands Download BMP Logo Select Bit Image Mode Dot Single-Density Mode Select Single-Density Graphics Print Advanced Raster GraghicsValue of r Data bytes Select Double-Density Graphics Select the Current Logo Define Downloaded Bit Image Convert 6 Dots/mm Bitmap to 8 Dots/mm Bitmap Print Downloaded Bit ImageHexadecimal 1D 2F m Decimal Value and Range of m Status Commands Status Command IntroductionBatch Mode ESC u Transmit Peripheral Device Status RS-232C printers onlyHexadecimal 1B 75 Decimal 27 117 Value of returned byte Hexadecimal 1B 75 n Decimal Hexadecimal Decimal Values Transmit Paper Sensor Status Transmit Printer ID Values of n Transmit Printer ID, Remote Diagnostics Extension Programming Information A794 Owner’s Guide December 107 Undefined. Fixed to off Send Printer Software Version Real Time Commands Preferred ImplementationAlternate Implementation Moving Data through the Buffer Rules for Using Real Time Commands Busy Line and Fault Conditions Real Time Status TransmissionRelated Information = Transmit Printer Status = Transmit RS-232C Busy Status = Transmit Error Status = Transmit Receipt Paper Status Real Time Request to Printer Real Time Printer Status Transmission Ascii GS ENQValue of Byte Auto Status Back Select or Cancel Automatic Status Back ASB 118 December December 119 Recognizing Data from the Printer Select Printing Position of HRI Characters Bar Code CommandsSelect Pitch of HRI Characters Select Bar Code Height GS k m n d1…dn 1D 6B m n d1…dn 29 107 m n d1…dn Print Bar Code CODE39 Select Bar Code Width Print and Return to Standard Mode Mode CommandsCancel Print Data in Page Mode Ascii FF Select Page Mode Print Data in Page ModeAscii ESC FF Ascii ESC L Select Standard Mode Select Print Direction in Page ModeAscii ESC S N1-4 = N5 = N6 = N7 = N8 = Set Print Area in Page Mode Set Absolute Vertical Print Position in Page Mode Set Relative Vertical Print Position in Page Mode Macro Commands Select or Cancel Macro DefinitionHexadecimal 1D 3A Decimal Value of t Execute Macro Write to User Data Storage User Data Storage CommandsRead from User Data Storage Read from Non-Volatile Memory December 133 Flash Memory User Sectors Allocation Erase User Flash SectorGS U n1 n Switch to Flash Download Mode Flash Download CommandsPrinter operation ESC Return Segment Number Status of Flash Memory Return Boot Sector Firmware Part NumberSelect Flash Memory Sector to Download Get Firmware CRC Return Microprocessor CRC Erase All Flash Contents Except Boot SectorReturn Main Program Flash CRC Erase Selected Flash Sector Download to Active Flash Sector Reset FirmwareAscii GS Space 1D FF Basic Index DOS December 141