ENGLISH
Error messages
An error message is displayed if Audyssey® Auto Setup could not be completed due to speaker placement, the measurement environment, etc. If this happens, check the relevant items, be sure to take the necessary measures, then perform Audyssey Auto Setup over again.
NOTE
Be sure to turn off the power before checking speaker connections.
| Examples | Error details | Measures |
|
|
|
|
| Caution | • The connected setup microphone is broken, or a | • Connect the included setup microphone to the |
| device other than the supplied setup microphone | SETUP MIC jack of this unit. | |
| MultEQ | ||
| FMicrophone:None | is connected. |
|
| or |
| |
| • Not all speakers could be detected. |
| |
| Speaker :None |
| |
|
| • The front L speaker was not properly detected. | • Check the speaker connections. |
| Retry |
|
|
| Cancel |
|
|
| [ENT]:Retry |
|
|
|
|
|
|
| Caution | • There is too much noise in the room for accurate | • Either turn off any device generating noise or |
| measurements to be made. | move it away. | |
| MultEQ | ||
| FAmbient noise is |
| • Perform again when the surroundings are quieter. |
| too high or |
| |
| • Speaker or subwoofer sound is too low for | • Check the speaker installation and the direction | |
| Level is too low. | ||
|
| accurate measurements to be made. | in which the speakers are facing. |
| Retry |
| • Adjust the subwoofer’s volume. |
| Cancel |
|
|
| [ENT]:Retry |
|
|
|
|
|
|
| Caution | • The displayed speaker could not be detected. | • Check the connections of the displayed speaker. |
|
|
| |
| MultEQ |
|
|
Front
R:None
Retry
Cancel
Skip
[
]:Up/Down [
]:CH
Caution | • The displayed is connected with the polarities | • Check the polarities of the displayed speaker. | ||||||
reversed. | • For | some speakers, | this | error message may | ||||
|
| MultEQ | ||||||
|
|
|
| be | displayed even if | the | speaker is properly | |
| Front |
|
| |||||
|
|
| connected. If you are sure the connection is | |||||
| L :Phase |
|
| |||||
| Retry |
| correct, press ui to select “Skip”, then press | |||||
|
| ENTER. |
|
| ||||
| Cancel |
|
|
| ||||
| Skip |
|
|
|
|
| ||
[ ]:Up/Down [ ]:CH |
|
|
|
|
| |||
Parameter Check
This function enables you to check the measurement results and equalizer characteristics after Audyssey Auto Setup.
1 Use ui to select “Parameter Check” and then press ENTER.
2 Use ui to select the item you want to check, then press ENTER.
Speaker Config.Check
Distance Chenck
Channel Level Check
Crossover Freq.Check
EQ Check
Restore
[ENT]:Select [RTN]:Back
Speaker Config. Check Check the speaker configuration.
Distance Check | Check the distance. |
Channel Level Check Check the channel level.
Crossover Freq. Check Check the crossover frequency.
EQ Check | Check the equalizer. |
•If “EQ Check” is selected, press ui to select equalizing curve (“Audyssey” or “Audyssey Flat”) to be checked.
Use o p to switch the display between the different speakers.
3 Press RETURN.
The confirmation screen reappears. Repeat step 2.
Retrieving Audyssey Auto Setup settings
If you set “Restore” to “Yes”, you can return to Audyssey Auto Setup measurement result (value calculated at the start by MultEQ®) even when you have changed each setting manually.
10
Remote control operation | Move the cursor | Confirm the setting | Return to previous menu | |
buttons | (Up/Down/Left/Right) | |||
|
|
