Marantz NR1601 Troubleshooting, English, If a problem should arise, first check the following

ENGLISH

Troubleshooting

If a problem should arise, first check the following:

1.Are the connections correct?

2.Is the set being operated as described in the user guide?

3.Are the other components operating properly?

If this unit does not operate properly, check the items listed in the table below. Should the problem persist, there may be a malfunction.

In this case, disconnect the power immediately and contact your store of purchase.

GGeneralH

Symptom	Cause/Solution	Page
Power does not turn	• Check whether the power plug is correctly inserted into the power	5
on.	outlet.
	• The protection circuit is active. Disconnect the power plug from	4, 71
	the electric outlet, wait 5 to 10 seconds and then insert it back
	into the outlet.
Display is off.	• Set “Display” on the menu to something other than “OFF”.	53
The power indicator	• The temperature inside the unit has risen. Please turn off power	–
is blinking red	once, and re-apply the power after the temperature has fallen
in intervals of	sufficiently.
approximately 2	• Please re-install this unit in a place having good ventilation.	–
seconds.
The power indicator	• Please use speakers which have the specified impedance.	4
is blinking red	• The speaker cable has shorted (is touching). Firmly twist the core	4
in intervals of	wire in the speaker cable, and then re-connect it to the speaker
approximately 0.5	terminal.
seconds.
After turning on the	• This unit amplifier circuit has failed. Turn off the power and please	–
power, the power	contact the Marantz service adviser.
indicator is blinking
red in intervals of
approximately 0.5
seconds.
Set does not operate	• Reset the microprocessor.	74
properly.
GVideoH
Symptom	Cause/Solution	Page
No picture appears.	• Check the TV connection.	5
	• Set the TV input correctly.	6
The on-screen	• Set the on-screen display output mode to match your TV and	54
display is not shown.	connection method.
Or noise occurs.

GAudioH

Symptom	Cause/Solution		Page
Audio is not output.	• Check the connections for all devices.		5, 14 – 20
	• Check the speaker connections.		5, 31, 32
	• Check whether the audio device power is turned on.		–
	• Adjust the master volume.		21
	• Cancel the mute mode.		21
	• Select a suitable input source.		21
	• Select a suitable input mode.		43
	• Disconnect the headphones. No sound is output from the speakers		60
	or the PRE OUT connectors when headphones are connected.
No sound is	• Check if the surround speakers are connected to the SURROUND		–
produced from	terminals.
surround speaker.
No sound is	• Set “Amp Assign” on the menu to “Normal”.		49
produced from	• Set “Speaker Config.” – “S.Back” on the menu to something		50
surround back	other than “None”.
speaker.	• Set the surround mode to something other than “STEREO”.		26
No sound is	• Set “Amp Assign” on the menu to “Normal”.		49
produced from front	• Set “Speaker Config.” – “Surround” on the menu to something		50
height speaker.	other than “None”.
No sound is	• Check the subwoofer connections.		5, 31, 32
produced from	• Turn on the subwoofer’s power.		6
subwoofer.	• Set “Speaker Config.” – “Subwoofer” on the	menu to “Yes”.	49
	• If “Front” and “Center” for “Speaker Config.”	are set to “Large”,	49, 50
	and “Subwoofer Mode” is set to “LFE”, no sound may be output
	from the subwoofers, depending on the input signal or selected
	surround mode.
DTS sound is not	• Set “Decode Mode” on the menu to “Auto” or “DTS”.		44
output.
Dolby TrueHD, DTS-	• Make HDMI connections.		14
HD, Dolby Digital
Plus audio is not
output.

72