Marantz NR1601 manual Ghdmih, GRadioH, GiPodH, GM-XPortH

	SVENSKA	NEDERLANDS
GHDMIH
Symptom	Cause/Solution		Page
No audio is	• Check the connection of the HDMI connectors.		14
output with HDMI	• When outputting HDMI audio from the speakers, set “HDMI		51
connection.	Audio Out” on the menu to “Amp”.
	• When outputting HDMI audio from a TV, set “HDMI Audio Out”		51
	on the menu to “TV”.
No video is	• Check the connection of the HDMI connectors.		14
output with HDMI	• Set the input source to match the connected HDMI connector.		14, 21
connection.	• Check whether the TV is compatible with copyright protection		14
	(HDCP). If connected to a device not compatible with HDCP, video
	will not be output correctly.
When the following	• Set “HDMI Control” on the menu to “OFF”. To operate power		35, 51
operations are	only for each device, set “Power Off Control” to “OFF”.
performed on
devices compatible
with HDMI control,
the same operations
occur on this unit.

•Power ON/OFF

•Switching audio output devices

•Adjust volume

•Switch input source

GRadioH

Symptom	Cause/Solution	Page
Reception fails, or	• Change the antenna orientation or position.	20
there is a lot of noise	• Separate the AM loop antenna from the unit.	20
or distortion.	• Use an FM outdoor antenna.	20
	• Separate the antenna from other connection cables.	20
GiPodH
Symptom	Cause/Solution	Page
iPod cannot be	• Check the iPod connections.	18
played.	• Switch the input source to “USB”.	21
	• Incompatible iPod types cannot be played back.	18
“Connection Error”	• Unable to communicate properly. Turn off the power to this unit,	–
is displayed.	disconnect the iPod and then reconnect it.

ESPAÑOL	ITALIANO	FRANÇAIS	DEUTSCH	ENGLISH
GUSB memory deviceH
Symptom		Cause/Solution			Page
When a USB	• The set cannot recognize a USB memory device. Check the				18
memory device is	connection.
connected, “USB” is	• A USB memory device not conforming to mass storage class is				–
not displayed on the	connected. Connect a USB memory device conforming to mass
menu.	storage class.
	• A USB memory device cannot be connected via a USB hub.				18
Files on a USB	• Set the USB memory device format to “FAT16” or “FAT32”. For				–
memory device	details, refer to the USB memory device’s operating instructions.
cannot be played.	• If the USB memory device is divided into multiple partitions, only				–
	files stored in the top partition can be		played.
	• The file is recorded in an incompatible format. Please record it in				–
	a compatible format.
	• This unit cannot play back files covered by copyright protection.				–
The file names	• Characters that cannot be displayed on this unit are replaced by				22
are not displayed	“.” (period).
properly (“...”, etc.).
The sound quality is	• The file being played	back has a low	bit rate.		–
poor or there is noise
during playback.
“Connection Error”	• Unable to communicate properly. Turn off the power to this unit,				–
is displayed.	unplug the USB memory device and then plug it back in.
	• The USB memory device is not responding. Turn off the power to				–
	this unit, unplug the USB memory device and then plug it back in.
“Overcurrent” is	• The USB memory device is consuming too much power. When				–
displayed.	using a USB portable hard disk that can be powered by an AC
	adapter, connect its AC adapter.
GM-XPortH
Symptom		Cause/Solution			Page
Audio is not output	• Check that the Bluetooth device and Wireless receiver (RX101)				–
when a wireless	are correctly paired.
receiver (RX101 is
connected).
GRemote control unitH
Symptom		Cause/Solution			Page

Simple version

Basic version

Advanced version

“Not Support” is	• The iPod connected to the unit is not compatible. Please make	18
displayed.	sure the iPod you are connecting is compatible.
	• The software version of the connected iPod is an old one. Please	–
	update to the latest version.
“Connection Error”	• The iPod is not responding. Turn off the power to this unit,	–
is displayed.	disconnect the iPod and then reconnect it.

The set cannot be operated with the remote control unit.

•Batteries are worn out. Replace with new batteries.

•Operate the remote control unit within a distance of about 7 m from this unit and at an angle of within 30°.

•Remove any obstacle between this unit and the remote control unit.

•Insert the batteries in the proper direction, checking the q and w marks.

•The set’s remote control sensor is exposed to strong light (direct sunlight, inverter type fluorescent bulb light, etc.). Move the set to a place in which the remote control sensor will not be exposed to strong light.

64

64

64

64

64

Information

73