ENGLISH
Setting items | Setting details |
|
|
Height Gain | Low : Reduce the front height channel volume. |
Control the front height | Mid : Front height channel sound is output with standard sound volume. |
channel volume. | High : Increase the front height channel volume. |
NOTE
| “Height Gain” is displayed for the following settings. |
| • When “Amp Assign” (vpage 49) is set to “Front Height”. |
| • When the “Speaker Config.” – “Front Height” setting (vpage 50) is set |
| to other than “None”. |
| • When surround mode is “PLgz” or the PLgz decoder is used. |
Default | Yes : Reset to the defaults. |
The “Surround Parameter” | No : Do not reset to the defaults. |
settings are returned to the default settings.
Tone | Default settings are underlined. |
Adjust the tonal quality of the sound.
Setting items | Setting details |
|
|
Tone Control | ON : Allow tone adjustment (bass, treble). |
Set the tone control function OFF : Playback without tone adjustment. | |
to ON and OFF. | “Tone Control” can be set when “Dynamic EQ” (vpage 47) is set to |
| |
| “OFF”. |
NOTE
The tone cannot be adjusted in the direct mode.
Bass | ||
Adjust low frequency range | “Bass” can be set when “Tone Control” is set to “ON”. | |
(bass). | ||
| ||
Treble | ||
Adjust high frequency range | “Treble” can be set when “Tone Control” is set to “ON”. | |
(treble). | ||
|
| Audio Adjust |
Audyssey Settings | Default settings are underlined. |
Set MultEQ®, Dynamic EQ® and Dynamic Volume®. These can be selected after Audyssey® Auto Setup has been performed. For additional information on Audyssey technology, please see page 70.
NOTE
If you have not performed Auto Setup, or if you change the speaker settings after performing Auto Setup, you may not be able to select Dynamic EQ/Dynamic Volume, and “Run Audyssey” may be displayed.
In this case, either perform Audyssey Auto Setup over again or perform “Restore” (vpage 10) to return to the settings after Audyssey Auto Setup was run.
Setting items | Setting details | |
|
| |
MultEQ | Audyssey : Optimize the frequency response of all speakers. | |
Select one equalizer from | Audyssey Byp.L/R : Optimize frequency response of speakers except | |
three modes. MultEQ | front L and R speakers. | |
corrects both time and | Audyssey Flat : Optimize frequency response of all speakers to flat | |
frequency response | response. | |
problems in the listening | Manual : Apply frequency response set with “Manual EQ” (vpage 48). | |
area based on Audyssey | OFF : Turn “MultEQ” equalizer off. | |
Auto Setup calibration. We |
| |
recommend “Audyssey”. | • “Audyssey”, “Audyssey Byp. L/R” and “Audyssey Flat” can be | |
MultEQ is the prerequisite | ||
selected after Audyssey Auto Setup has been performed. “Audyssey” | ||
function for Dynamic EQ | ||
is automatically selected after performing Audyssey Auto Setup. When | ||
and Dynamic Volume. | ||
“Audyssey”, “Audyssey Byp. L/R” or “Audyssey Flat” is selected, | ||
| ||
| illuminates. |
•After running Audyssey Auto Setup, if the Speaker Configuration, Distance, Channel Level, and Crossover Freq. have changed without
increasing the number of speakers measured, only illuminates.
• Press MULTEQ on the remote control unit to set this setting.
NOTE
•“MultEQ” and “Manual” cannot be selected when “EQ Customize” is set to “Not Used” (vpage 52).
•When using headphones, “MultEQ” is automatically set to “OFF”.
46
Remote control operation | Move the cursor | Confirm the setting | Return to previous menu | |
buttons | (Up/Down/Left/Right) | |||
|
|