ENGLISH
Perform this procedure if the display is abnormal or if operations cannot be performed. When the microprocessor is reset, all the settings are reset to their default values.
Various setting details can be saved and reset on this device. If setting details are saved before returning to the default values, after returning to the default settings, setting details can be returned to the same values as before returning to the defaults.
To return all of the settings to the default values, perform steps 2 to 4 without performing step 1.
ON/STANDBY |
| ENTER STATUS | |||||||||||||||||||
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
1 When the power is ON, press and hold STATUS and ENTER for more than 3 seconds. After “MEMORY SAVING” is shown on the display, “COMPLETE”is shown to inform you that the settings have been saved.
4 Once the display starts flashing at intervals of about 1 second, release the two buttons.
After “MEMORY LOAD” is shown on the display, “COMPLETE” is shown to inform you that the settings have returned to those saved in step 1.
If in step 4 the display does not flash at intervals of about 1 second, start over from step 2.
nn Audio section
• Power amplifier |
|
|
|
|
Rated output: | Front: |
|
| |
| 50 | W + | 50 W (8 Ω, 20 | Hz – 20 kHz with 0.08 % T.H.D.) |
| 75 W + | 75 W (6 Ω, 1 kHz with 10 % T.H.D.) | ||
| Center: |
|
| |
| 50 | W (8 Ω, 20 Hz – 20 kHz with 0.08 % T.H.D.) | ||
| 75 | W (6 Ω, 1 kHz with | 10 % T.H.D.) | |
| Surround: |
|
| |
| 50 | W + | 50 W (8 Ω, 20 | Hz – 20 kHz with 0.08 % T.H.D.) |
| 75 W + | 75 W (6 Ω, 1 kHz with 10 % T.H.D.) | ||
| Surround Back: |
| ||
| 50 | W + | 50 W (8 Ω, 20 | Hz – 20 kHz with 0.08 % T.H.D.) |
| 75 W + | 75 W (6 Ω, 1 kHz with 10 % T.H.D.) | ||
Output connectors: | 6 – 8 Ω |
|
| |
• Analog |
|
|
|
|
Input sensitivity/Input impedance: | 130 mV/50 kΩ |
| ||
Frequency response: | 10 Hz – 100 kHz — ±3 dB (Source Direct mode) | |||
S/N: | 98 dB |
nn Video section
• Standard video connectors |
|
Input/output level and impedance: | 1 |
Frequency response: | 5 Hz – 10 MHz — +1, |
• Color component video connector |
|
Input/output level and impedance: | Y (brightness) signal — 1 |
| PB / CB signal — 0.7 |
| PR / CR signal — 0.7 |
Frequency response: | 5 Hz – 60 MHz — +0, |
nn Tuner section |
| [FM] | [AM] |
| (Note: μV at 75 Ω, 0 dBf = 1 x |
| |
Receiving Range: | 87.5 MHz – 107.9 MHz | 520 kHz – 1710 kHz | |
Usable Sensitivity: | 1.2 μV (12.8 dBf) | 18 μV | |
50 dB Quieting Sensitivity: | MONO | 2.8 μV (20.2 dBf) |
|
S/N | MONO | 70 dB |
|
| STEREO 67 dB |
| |
Total harmonic Distortion (at 1 kHz): | MONO | 0.7 % |
|
nn General | STEREO 1.0 % |
| |
|
|
| |
Power supply: | AC 120 V, 60 Hz |
| |
Power consumption: | 250 W |
|
|
| 0.2 W (Standby) |
| |
| 3 W (CEC standby) |
| |
Maximum external dimensions: | 440 (W) x 105 (H) x 367 (D) mm |
| |
Weight: | 9.0 kg |
|
|
nn Remote control unit (RC010SR)
Batteries: | R03/AAA Type (two batteries) |
For purposes of improvement, specifications and design are subject to change without notice.
74