!Assembly of LCD Back Damper (Applicable Model : Digitizer Model)
Digitizer PCB Assy
| Detail of "A/B/C" | |
| Pass the Cable | 0~0.5mm |
LCD Back Cushion DG CCFL | under the protrusion. | |
A | B | C |
Screw the Digitizer
and the LCD Back Dumper together.
Screw
0~3mm
|
|
| LCD Back Dumper | LCD Back | ||
|
|
| Remove the Release Paper on the back side and attach it. | |||
Digitizer |
| 4±0.5mm | Lengthwise: Match to the LCD Frame. |
| Cushion | |
|
| |||||
|
| Crosswise: Match to the middle line. |
| DG Side | ||
Handle it carefully. |
|
|
|
| ||
|
|
|
|
| ||
Digitizer PCB Assy
Screw the Digitizer and the LCD Back Dumper together.
Screw
2±0.5mm
Digitizer Sheet
LCD Side |
|
| 2±0.5mm LCD Back Cushion DG Side |
|
| ||
Cushion A |
|
| |
Ensure the | Tape |
Fold back the half length, |
0~0.5mm
0~0.5mm
Attach it to the side |
|
surface of the Frame. |
(Match to the end of |
the Frame within 0 to 0.5 mm |
at the far side.) |
10±2mm |
|
| ||
Connector is | and attach to the LCD side. | ||
| |||
connected |
|
| |
| 10±2mm | ||
securely. |
| ||
| |||
Fold back the surplus length.
Screw the Board together. |
|
| |
Screw |
|
| |
| 0±0.5mm | LCD Side | 0±0.5mm LCD Side Cushion D |
|
| Cushion C |
|
|
| 0±0.5mm | 0±0.5mm |
|
|
| |
Screw the Board together. |
Screw
LCD Side Cushion C
0±0.5mm
0±0.5mm
!Assembly of Inverter PCB (Applicable Model : Touch Screen Model)
Safety Working
| Prevent FPC from coming off. | LCD Side Cushion E | ||||
Insulation Parts |
| Insert between | Avoid any stress on the Cable | |||
12 |
|
| ||||
|
| Connector |
| the ribs. | when connecting it | |
LCD Side Cushion E | FPC | PWB |
|
| to the Inverter. | |
|
| (Hold the Connector part | ||||
Insert between the ribs. |
| LCD Side Cushion F | Caution High | when connecting | ||
TS PWB | Voltage Label | /disconnecting.) | ||||
|
| |||||
| Insert | Insert between the ribs. |
| |||
|
|
| 0~3mm |
| ||
|
|
|
|
| ||
Inverter Assy
LCD REAR Side
| Pay attention to the direction of | |
| the INVERTER PCB when doing | |
| this installation. | INV MIL Sheet |
| 30~35mm | |
|
| |
Inverter Case MIL |
| ("Gap side" is front.) |
INV Sheet 1 |
| INV MIL Cover |
|
| |
(Black) |
|
|
5~6mm |
| Insert |
LCD Cable Connector side |
|
|
Inverter |
| Insert |
|
| CCFL |
5~6mm | Connector | |
side | ||
|
INV Sheet 2
(Translucence)
Detail of "A"
Safety Working |
Confirm a "Insulation |
Parts" isn’t frayed. |
1~2 |
mm |
| 0~0.5mm |
|
| Inverter Assy |
|
|
| ||
| PET TAPE 1 |
|
| Connect | the Cable to the | left | Tape |
| |
|
|
|
| and right Connectors. |
|
| |||
|
|
|
|
|
| Attach so the Inverter Assy | |||
Avoid any stress on the Cable |
|
|
| ||||||
when connecting it to the Inverter. |
|
|
| comes at the center, | |||||
(Hold the Connector part |
|
|
| and attach the left and right | |||||
when connecting/disconnecting.) | LCD Cable |
| surplus length to the Back Dumper | ||||||
|
|
|
| as illustrated below. | |||||
Sield Sheet | Safety Working | Carefully attach Tape | Tape |
|
|
| |
pasted on the connector |
| Inverter Assy | |
after it is wound around | Insulation Parts | LCD Back Dumper | |
the cable twice. |
|
| |
| Fix the two Cables. |
|
|
|
| 0~3mm |
|
Avoid getting under the Sheet.
A
Don’t give stress to LCD TAB. | ANT Cable Cushion | Conductive Tape | |
Wrap over the Antenna Cable | |||
| Wrap. | ||
|
| Cushion and the Cable. |
